Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Running 7.2.110.0 code.Question:I had been working with an EAP WLAN testing for awhile in preperation for a project and had it work well with a single SSID and upon login and authentication, an attribute was passed by ACS to the WLC to point the clie...
Hello,I am trying to config my wireless lan controller (WLC) 2106 to discover my new 3500 access points.I followed the example Cisco configuration doc. 69719.I am using a Cisco 3760 switch to interconnect the AP and WLC.I set up DHCP in the switch.I ...
In my WLAN enviornment there are multiple heavy, block walls. In some locations the AP may be stored securely in a closet while the antennas are routed through the ceiling and down into a room with concrete block walls. What I'm wondering is, how can...
Resolved! 5GHz Antennas on 2.4GHz radio?
Hi,This might be kind of a stupid question, but I can't find anything about this on the internet.It is as following:We ordered 2 Cisco AIR-LAP1242AG-E-K9 Wireless Access Points with 4 AIR-ANT5135D-R antennas.We accidentally ordered the 5GHz antennas ...
We have Cisco MSE running wIPS mode. Cisco wIPS cost: License for wIPS, Cost of MSE, License for WLC, LIcense for WCS and cost of AP to deploy. This is expensive package and it is still not comprehensive. So many false alerts...signatures get upda...
HiI would just like to know how or wot to do if i want a system in place as the wcs software. currenlty we are running the flex connect 7500 controller with fw 7.2.103.0 as i see on the compatibily matrix of the wcs it doesnt support this firmware. w...
I´ve a 877W router that disconnects wirelless clients one or two times per minute.In syslog appears many times the following messages:DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the client.I was looking in cisco ...
Hi All, I have a lightweight AP that boots into Romon, if i hold the reset button in for 10 seconds or so it will boot into the IOS and download the config from the controller but never registers. then once i reboot it it goes back to Romon unless i ...
Dears i have WLC 5508 showing the below Logs , which prevent the users from connecting to the SSIDs , also its disconnecting the associted users DHCP Socket Task: Jul 11 09:54:08.992: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DH...
I have 2 5508s (foreign and anchor both running 7.2.110.0) with an open WLAN configured via mobility anchors. This configuration works and has no problems. My next task is to incorporate a webauth page (accept/reject) to present the clients with AUP ...
In a mesh network, i understand each radio interface works on a specific speed. some refer to as back haul.How do we find what is the speed the back haul radio is using in an access point used in such a network.any commands for this? thanks in advan...
Resolved! Push preshared WPA2 key to an iPad
Hi,Is there any way to push a preshared key to a WLAN client such as an iPad, or must staff touch each unit?Thanks.
Hi,From what I've read, it doesn't seem possible to use Web Authentication and obtain encryption unless using a Radius server. I have a client asking for web auth, encryption, and ldap connection to their AD servers.Not possible, right?Thanks.
I have a single client that is having issues staying connected to my WLC running code 7.0.220.0Here are the debugs, it just keeps on looping:-------------------------------------------------------------------------------------------------------------...
We are installing outdoor AP's and need info on how high the 2506 mast mount antenna's can be mounted. Cisco says 10 - 15 feet. We are using the outdoor 1310 AP's to cover scanning of steel coils at our facility. The coils are mostly stacked 2 h...
