Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi,my question regards to a pair of WLC 4402 with 7.0.98.0 software.Actual, our security policy does not really allow any peer-to-peer communication in a wireless LAN. Therefore we set the 'P2P Blocking Action' to drop, and the 'Broadcast Forwarding'...
Hello all,We are using the built-in DHCP server on the WS-C3750G-24WS-S25 controller to distribute IP addresses to our (wireless) guest VLANs.Our guest VLAN has grown a lot and lately we are experiencing DHCP problems (long time to get an ip or renew...
Hello,Does anyone know where to find information about CAPWAP-3 messages like these ?%CAPWAP-3-ERRORLOG: Failed to send data transfer request.%CAPWAP-3-ERRORLOG: Queue already full.Thanks in advance.
I Would like the WLAN users to get authenticated one time using username and password , im wondering which method can be used .
Having problems getting an incommon cert to import to WCS. No success using the http://www.cisco.com/en/US/products/ps6305/products_configuration_example09186a00809d50f4.shtml?referring_site=smartnavRD Also not Linux savvy by any means.
I want to use the WAP200E-EU in an outdoor café. I have read in its PDF that this AP creates a bubble so I imagine that it sends the signal in 360 degrees but it also says it has a directional antenna. Does this means that you have the option to sele...
Hi,In our factory's mesh network, there are temperature/air sensing sensors connected to mesh network. Now in one of the corner locations, there is an mesh ap. a new similar sensor is to be installed near this mesh ap point for sensing that area. But...
Lets say i have a 5508 wlc and have configured a wlan with web-auth and radius authenticationThe one and only configured radius server goes offline. In the event this should happen, is it possible to allow clients to connect anyway? auth none as seco...
I am trying to install a AIR-BR1310G wireless link between two buildings. I configured the setup in a lab and had everything functioning. Shipped it to the client who is now trying to install it. The radio link is up, but we are having issues with...
Newly installing a Cisco AP541n. Can I use the same power over ethernet adapter as I've used for the Cisco 1100?
HiNeed some help. I have setup guest access on the controller and this is not working at the moment.DHCP server setup on the controller for the Guest users.You are able to connect (get ip address from controller) and the browser gets redirected to 1....
I have multiple 1142 and 1252 access points on a 5508 controller. I only allow Internet access to devices/users that have authenticated to Active Directory. I'm seeing lots of traffic from my access points trying to access http://mus.cisco.com. Wh...
All,I have fat fingered an ACL on my VTY for an Autonomous 1240AG AP. So I am unable to SSH/telnet into the AP. I can however still HTTP into it. Is there a way to remove the VTY ACL from the web interface? or do I have to rest it?Thanks for your hel...
Hi,I am planning to have FAT access point 1242 connected to AIR-ANT2506 external Antenna.Are these two things compatible?Secondly, AP and Antenna will be 230 feet away, hence I am planning to buy a cable from Cisco (Part Code AIR-CAB050LL-R)Is this...
I am upgrading from 7.0.98 to 7.0.116I have downloaded the code to the controller. I predownloaded the code to the access points. I did a image swap, but the AP's still show 7.0.98 as primary and now the backup image as well, with 7.0.116 as the...
