Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Bonjour à Tous, Je m'en remets à vous car étant réellement très très nulle en informatique, je ne sais vraiment pas comment mettre à jour le pilote de ma carte réseau sans fil, car c'était une version de 2004 et je ne suis pas en mesure d'y arriver t...
I've begun implementing FlexConnect in my environment. So far, so good... everything is working mostly as expected.However, I now have a number of devices... certain smartphones so far... that will NOT connect to a FlexConnect AP if it's a 1262AGN AP...
Is the cisco wlc 2504 compatible with the AIR-CAP-3602l and if so what firmware would i need to be running on the WLC ? My firm rushed out and bought a mesh solution without doing their homework
I have a customer with a point to point wireless bride using two 1240 ap's. Every 12 minutes or so, the MAXRETRIES: maximim is reached, the client is deauthenticated becasue the previous authentication is not valid. The client then reassociates. T...
HelloWe all know that the 600 can streamline traffic so you can create two SSIDs one for office working applications and another for personal use eg traffic.What I want to know was that is it possible to use one SSID tunnelling back to the office wit...
Hi ,We are trying to migrate WCS base license to NCS 1.1 .We have procured the migration license .In the licensing guide , it is mentioned as "L-WCS-NCS1-M-K9 License first, before adding the licenses migrated from your WCS installation" I got some c...
We have a 5508 controller, one WLAN, and all of our internal wireless goes through that. We are looking into starting a guest WLAN. The internal wlan goes through one VLAN. What is going to be the best way to set up the guest wlan? I am assuming that...
Hi , i have 2 1260 Access points one is in root mode , one is wgb mode. Authentication is EAPFAST. There are 5 devices connected via WGB bridge to the rest of the network. - If clients are sending some data , then WGB AP announces this client mac via...
Hi all,While trying to connect to WiFi at remote sites APs, the connection is getting time out.User are getting error as 'Unable to connect to <WiFi-SSID>'The APs at corporate office are functioning properly and user are able to connect to the APs.Wi...
Hi all.I was to day to finalise the migration of a customer network to HA-SSO enabled central controllers. However on one site this failed. Unfortunately the ordering or delivery had been mismatched in a recent additional controller ordered with HA-S...
An interesting issue (I think).If a new client joins the WLAN, WPA and webauth works fine and the client is able to access the network.Webauth is using LDAP (active directoy). The same client returns the next day and he is unable to...
Hello all,I was just reviewing the config guide for 7.3 and HA-SSO and then I found out that with 7.4 it allows for an N+1 scenario.http://www.cisco.com/en/US/prod/collateral/wireless/ps6302/ps8322/ps10315/qa_c67-714540_ps2706_Products_Q_and_A_Item.h...
Hi all,I plan to replace 2 x WISM1 (WLC 6.0.182) by 2 x WISM2 (WLC 7.2.115.1). One WISM in each Catalyst 6500. I am sorry it is a little long but I have no lab and I need your advice. Summarized migration plan is the following : Upgrade of the 4 WLC ...
I am having difficulty finding information about all of the models of access points that can be setup as mesh access points. Can someone provide me this information or a link to that info? Greatly appreciated.
I've got a wes610n Cisco/Linksys that I'm trying to connect to our wireless network to use as a network adapter. I was able to get it connected to the network with a static address to the wireless, but I cannot ping it. On the wlc it shows connecte...
