Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I have inherited a WAP4400n, which I've tried to reset to the default settings by holding the reset button in for 10 to 30 seconds. Powering it off and then back on - multiple times. I've then tried to connect to it via cat 5 cable from my laptop to...
Hias far i know if i try to login to the domain with wireless connection in a laptop instead of wired i get the error message that domain not available, this is basically because you are not connected the network .i.e your wireless card only connect...
Hi AllI got task to design enterprise wide wireless solution for my client. There are 50+ offices from 20-600 users. Offices are mostly connected as a hub and spoke by MPLS or VPN IPsec. Most of the office will have one or more WLC but some will have...
Hi, I have a requirement to put AP1242 as WGB in a bus. The power source available is the bus battery power which is only 12VDC. Is there any Cisco power injector or 3rd party power injector that can work on 12VDC to supply power to AP1242 ? regards...
currently have 3 - 1242g access points that are not being seen by WCS server. only one that is connected is 1231. any know issues with that model?
Resolved! WCS/AAA Cannot Run Reports
We are running WCS 7.0.1 and ACS 4.2 using TACACS for our techs to login to WCS (to manage access points). However, when the tech trys to run reports, they get an error:Permissions DeniedThe user is setup in Active Directory and not in WCS. I saw s...
Hi there,I am currently setting up a wireless controller which is to service several SSIDs which are mapped to physically separated LANs.So far there has been no problem in doing the config.However I discovered later that for each SSID a separate RAD...
For LAN design fine, keep the broadcast domain to an optimum size. What about WIFI design though ? I want to use just 1 SSID and can have multiple vlans if I use AP groups on the controller..But how big is optimum size for a WIFI subnet ? I guess i...
Hello I'm currentlly running Both Wired and Wireless GPO via Win2008r2, on my WIRED connections after clt-alt-del logoff my network connection stays open (pingable)While connected via wireless (WLC 5508 and WCS) Windows AD 2008r2 ;Radius Server 2003....
Hello ...Can someone tell me how I can see a list of clients connected to a specific access point using the WCS? I cant seem to find the location in WCS that provides this info.Also - can I specify which AP the client connects to via the WCS?Thanks,
Hello Guys,I'm wondering if it's possible to connect my Android Device (Sansung Galaxy S II) to the coorporate wireless network.Basicaly what i'm trying is to connect to a Wireless LAN with.[WPA2][Auth(802.1X + CCKM)]Radio Policy All 802.11a only 802...
Odd issue at my office. I've got an iPad2, which works without issue at home (1130 AP/ASA5505), but at my office, we have a 1200 series AP. It's hit and miss, but other people who bring iPads in have noticed the same issue--our internal SSID is non...
Good afternoon friends, I have a Cisco Aironet 1240AG where it is configured as an AP. I use a Pocket PC to access the AP, but after a period of use, the Pocket PC loses communication with the AP for a short period of time and the application th...
Hi,i have a problem with Cisco WLC 2106 (SW: 7.0.98.0) and LAP1262.The client roams to new AP, associates with the new AP and authentication (WPA2 with EAP-TLS) runs fine until WPA2 key exchange. The first WPA2-Key-paket from AP (1 / 4) is sent twice...
Maybe I am asking the wrong question. On my standalone Aironet 1142n web interface, under the association tab, I see several clients listed with an ip address of 0.0.0.0. Should I be concerned about this? why are these not cleared automaticly? I have...
