Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi Everyone, We have 5 access points deployed on each of Floor A and Floor B. The requirement is to block a specific client MAC address on Floor A, while allowing the same client to connect normally on Floor B. The WLAN is centrally switched using a ...
I would like to build a bridge between two Cisco switches. Because of the company I work for I have to Meraki devices. Has anyone been successful in building a bridge between two devices up to 2000 feet able? Currently I'm using these TP-Link Omada P...
Hey!So i have a C1111-8plte & AIRCAP2702I-E-K9. My question is how can a non network engineer setup these devices to work? And also is it possible to use the ap as a ap where you just connect it to a network and it work as any other ap?
Hello, I have an AIR-AP2802E-B access point. The regulatory domain for my country is -A, but I used to solve the problem by configuring it to US or Puerto Rico, but now it doesn't work; the radios stay off.
Resolved! Zabbix template for Cisco EWC kontroller
Hi guysI'm looking for a Zabbix template to monitor my small setup, which is based on a Cisco AP9105 with an EWC controller.Could you share something you have built with me? There is no such template available on the Zabbix server.I don't have high e...
Hi everyone! I was trying to figure out the answer to my question and I would like to confirm with you guys if I am correct
We have an architecture that includes 2 9800-40 WLCs with mobility group configured and successfully joined/connected. Exchange of information has been confirmed. Both Foreign controllers have Guest SSIDs anchored to the same 9800 Anchor. Clients are...
Hello,I hope you are well.I am struggling to find a compatible device for for using a fibre cable connection to another part of the building to then use an SFP POE Powered Converter to connect the Fibre Cable to and then have an ethernet cable to con...
Does anyone know please, if it's necessary to have these commands set on the wlan in order to get the APSP upgrade to work smoothly?wlan WL-CorpWifi 20 CorpWifi bss-transition bss-transition disassociation-imminentI think these may be on by default...
Hi Cisco,We understand this is a cosmetic bug and doesn't impact service.However, we'd like to inquire about the roadmap for its resolution. Do you have an estimated timeframe for when a fix might be implemented?
I'm in a bit of a bind. We have an office with 10 APs under an Embedded Wireless Controller on AP1. To give some background, we set things up with more or less default settings when moving in three years ago and it worked well. I am just a simple rou...
We are preparing new Meraki APs to replace non-Meraki units in a building. Part of the process includes connecting the devices to the network so they receive the config from the dashboard, firmware updates, etc. After they show on-line in the dashboa...
Resolved! MR SSID assign Client ip
Hello Community,I have a question regarding MR SSID settings.In the MR SSID configuration, VLAN tagging is enabled, and the VLAN ID configured for VLAN tagging is the same as the device management VLAN.What I would like to understand is this:When the...
I have one AP 9136 for my lab which is stuck at boot and it looks like it's missing boot image.I have an image file ap1g6a-k9w8-tar.17_18_1_8.tar and tftp server but can't seem to find a procedure on how to load this file and boot from it. If you can...
Hi everyone,I'm running into a frustrating "black hole" Wi-Fi scenario during WAN outages and am looking for some advice or workarounds.The Environment:Meraki MR access points broadcasting a corporate SSID.Standard laptops configured to prefer the co...
