Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
I have 14 unit of Air-AP1142n. No controller. All unit were in a warehouse, each of the AP distance each other around 40mI would like to use only 4 SSID instead of 14 SSID.Is it Ok if I select 4 AP -> use SSID 1 using channel 14 AP -> use SSID 2 usin...
Hi,We have a wireless network. There are two ssid's configured on the controller.The strange thing is , when we'r near to an access point , out of the two ssid's , one of them shows very less signal strength, whereas the other one has better signal ...
Customer is interested in deploying the 3600 AP's but will not be able to replace all his 1231's, any chance there is a release between 7.0.220.0 and 7.1.91.0 that will support both AP's?
I configured an AP to use dhcp, now I want to use the CLI to show which default gateway it picked up. "Show ip route" doesn't seem to be in its vocabulary. Does anyone know the correct statement? Also - for the AP to use dhcp to pick up the defaul...
Hi,Does anyone know if there is a tool like WCS Navigator, in order to use it to manage multiple NCSs?Regards,Theo
Hi,We've recently setup a WLAN infrastructure using a WLC2504 and Aironet 1261 LWAP's; two SSID's are configured on the WLC; one configured for Guest [using lobby ambasador] and one configured for Internal use.The requirement to deploy the Aironet 60...
Hi Guys,Can someone give me some advice? Its a bit long but challenging ..••JI am interested in implementing a Multiple WLC environment. I have Three 5508 controllers and 3 buildings (each building approx. 40 APs). I am considering 2 different approa...
hi,one of our customers wants to update the firmware of a 5508 wlc, but always gets the following error message:Error Message %UPDATE-3-INV_FILE_SIGN: Error! Invalid image signature!. Image may be corrupt.but the same image works fine on another 55...
Hello everybody,I will migrate a Cisco WLAN Controller 2125 to 2504,So I have one question?I need to make all configuration into the new Wlan Controller or I can migrate with one tool or something else?Best Regards
hello friends,if we have 2 cisco 2504 series wlcs and use multicast fetures in both and both are primary and secondry for LAPswhat about of we use multicast ip address let's say 255.239.1.60 can we use the same ip address for the secondry contrller ...
Hi All,I am able to view clients, rogue APs, rogue clients etc, but the information is faily inaccurate. Thus, I am trying to calibrate using the RF calibration models. I have created a new model and am attempting to add data points.After adding the ...
hi,one of our customers wants to update the firmware of a 5508 wlc, but always gets the following error message:Error Message %UPDATE-3-INV_FILE_SIGN: Error! Invalid image signature!. Image may be corrupt.but the same image works fine on another 55...
WCS fails to start with a Tomcat error , see below ;See launchout below - any ideas - without re-installing WCS Checking for Port 21 availability... OKChecking for Port 8456 availability... OKChecking for Port 8457 availability... OKChecking for Port...
Hi,I have an AP1242 that I am trying to set up but whenever I plug it in, it will go straight to the image recovery (pink status, red radio LED) and display the following:Xmodem file system is available.flashfs[0]: 148 files, 7 directoriesflashfs[0]:...
Hellowhat is the ideal timeout for users when no activity is performed while connected to network via wirelessWLC model 5500AP model 1200 seriesusers get disconnected every 15mins when machine is Ideal and where do i see this optionthanksST
