I am putting in a new 5508 controller. I've built the WLANs, activated the wireless, and configured the network for DHCP.When I add a new 1262 wireless AP to the network, it gets an address from DHCP, but then says it cannot communicate with the cont...
See below config. All IP Addresses are correct and I have other AP which works. However, this one does not. They are using the same RADIUS settings.On the client machine I am getting a EAP/TTLS box asking for Domain/Username and Password (Token). If ...
Hello,I was wondering if someone out there could help me with a problem with our WLAN. We recently received our WLC 5508, AP and switches to setup our WLAN but I'm having trouble getting it all to work. It's been months since the course and I'm hav...
Hi folks!I'm trying to use chain certificate for my devices authentication. can someone please help?'couse in cisco web page I saw that it's was only possible to use chain certificate for Web Auth.
Hi Guys, I want to cover an old building where just some cables can be run, so I would use mesh, but I want to use as many APs over wire as possible.Is it possible to have wireless mesh AND non-mesh Access Points to cover the same area? Are there any...
Hello,On a 4402 wireless controller (7.0.220.0) with LAP1242AG-E-K9 and LAP1252AG-E-K9 access points I receive lots of messages like this:Dec 9 12:55:16 ap-a1 1466: AP:001a.2f58.d4d6: *Dec 9 11:55:16.174: %LINK-3-UPDOWN: Interface Dot11Radio0, chan...
Hi All,I have a (single) client (it is a cisco IOS router) behind a wireless workgroup bridge (cisco1242).The client's IP address is obtained via DHCP from the wired network.Now, when roaming occurs, the Client will never have knowledge about this ev...
Afternoon,I am thinking of pushing out the H-REAP configuration to all my AP's on my local site for redundancy. I have read reems and reems of documentation on the matter but just want to throw a couple of ideas and questions around.Using PSK (WAP) I...
I am not able to see AP availability report in Cisco WCS. Please help me and see the snapshot.
Greetings everyone,we have done an wlc implementation to our customer using web auth via LDAP with custom web page and all things works fine.But now a customer wants to see a remaining lifetime of user account after successful login. Is it possible ...
HiI have a problem .Is there any easy way of mowing a large number of AP (50-100) from one”primary Controller” to another”primary controller” .It takes to long time to move each AP individualRegardsJohan Lindstrand
Hi!We got some serious issues to get APs running on a WLC 5508 (7.0.116.0). The APs were added and configured in the WCS, but no SSID can be found by clients (802.11b/g Network Status is enabled).The radio led is blinking green on the APs which indic...
I have never actually needed to use the service port of a WLC until today. We found an urgent need to tftp to a controller in the DMZ, and found that we could get to it easily because of change requests, etc.We configured the service port to 192.168...
Keep getting DHCP timeouts 169.254.x.x addressing. I think that the client laptop is not giving a response to the REQ from the DHCP server. Am I correct in my interpretation of the debug?00:21:d7:93:f9:40 from Disassociated to Idle*apfReceiveTask: ...
I was wondering if the 2504 has the lobby ambassador feature available. Customer requires temp username/passwords for guests managed through web gui. I couldn't find conclusive documentation it was included so I figured I'd check here before calling ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM | ||
| 08-06-2026 09:29 PM |
| User | Count |
|---|---|
| 5 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |
