Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hello!I have a Cisco 881W that will no longer boot/operate properly if the internal radio card is installed.If the card is installed, all I get is the following...System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)Technical Support: http:/...
Dear Friends, I have 1* 5500 series controller. I need to connect to two core switches which is configured as VSS. At present configuration in core switch is made as trunk port with native vlan assigned. On WLC , i have enabled LAG. I tried to config...
I am looking for the document the explains how client DHCP work? More specifically I am interested in how the DHCP relay function should be configured.As of now I have the Primary and Secondary DHCP server address configured on the dynamic interface...
I just purchased the AP1141N and I have created a logon account to access the device via URL which works fine but after 10 minutes it logs me out and requires that I log back on. Unfortunately it won't allow me to log back on unless I reset the devi...
I can't seem to find a way to set globally the Interal for automatic DCA on the WCS controller configuration templates.I am running 7.0.116.0 on the controllers and 7.0.220.0 on the WCS.Thanks for your help.JC
I am having an issue with internal and external clients. When we have the nat ip configured on the controller we cannot connect internal ap's at all. When we take the nat ip out it works fine. We are on code 7.0.220. I have tried the following comman...
Hi!I got a new task last week and can't solve the problem:There're two 3500er LAPs, which are controlled by a 2504 wireless controller. Each LAP is connected to a PoE-enable switch port (not directly to the 2504). Everything is fine: configuration vi...
Hi,we have a scenario with two remote sites. Site A is the central office and Site B is a remote location.In Site A we have a 6509 with WiSM and we have configured all the AP on these Wism (Site A + Site B APs).We need to use the same SSID in Site A ...
Hi AllIn Cisco NCS shell I have incorrectly entered the following command in order to chang ethe admin password and saved itusername admin password hash <password> role adminand hence lost the access to shell (ssh). Is there a way to retrieve or rese...
I have the situation where I need to talk to multiple different Radius servers depending on the WLAN. Some of the WLANs are not able to route traffic over my entire network, and within these secure areas the Radius server for that area sit. Is ther...
Hi Experts ,I have WCS 7.0.172.0 where as i have very frequent alert about DoS : CTS flood In channel 60, the system has detected 212 CTS frames in the last minute, which matches the traffic pattern of the form of denial-of-service attack, CTS (Clea...
Hi Friends,I have Cisco 1140 access points and 5508 controller in my network. I have configured 2 SSIDs. One SSID is working fine, we have issue with second SSID. Clients getting connected to second SSID are facing the latency issue, latency is aroun...
Hi all, appreciated if you guys can answer this.I have Cisco 2100 need to set up in DMZ and Air-Lap1131G as AP.Right now i connected the WLC console to a PC to run the initial bootup in terminal and i really need the info that it required.Now i have ...
Hi,My client has a wireless setup consisting of a WLC 2112 and about 7 1131AG LWAPPs. There are two SSIDs, say CORP(mapped to VLAN 900) and GUEST(mapped to VLAN 901). Wireless clients get IP through DHCP. DHCP IP is configured in the Dynamic interfac...
Hello,We have 2 Cisco Aironet Power Injector LR2's (AIR-PWRINJ-BLR2=) and I can't console to either using Cisco sky blue consoel cable.I am using putty and my setting are:Speed = 9600Data Bits = 8Stop Bits = 1parity = noneFlow control = none
