Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello Cisco Experts,I have a c9115 AP that laid on my table for a long time. Recently, I tried to bring it online, but failed initially to join to the WLC. After a reset the AP joined the WLC successfully and was working fine. For some reasons I did ...
Current setup:WLC 9800-L-F-K9 (Active) → Core Switch (Primary) → Active Gateway → FTD Firewall → Router → ISPWe have purchased another WLC 9800-L-F-K9 and need to configure High Availability (HA) between the two controllers.The new WLC will act as St...
Resolved! AIR-LAP1262N-A-K9
Hello there. I have this access point AIR-LAP1262N-A-K9, and it is autonomous and i want to convert in lightweight but i can not find the ios. Please how can i download anywhere ?
Hi Meraki Community I recently changed my router to MX65 and also added Meraki MR45 to boost my WiFi capability. Unfortunately after that change Sonos system and Google Chromecast Ultra stopped working. I tried reconnecting and looked for answers on ...
Hi, We had a simple network using the WiFi from our ISP's modem. Sonos speakers were connected using this SSID and everything was working great. Sonos speakers have a functionality that sync and plays simultaneously in all the spearkers using multica...
Hello Cisco WLAN experts,this 9800-80-WLC using 8 wncds shows a quite confusing distribution of Site-tags to wncd-processes:Initally I used a building/area-number inside each Site-Tag to add APs to it using Filters and Regex-expressions.But it looks ...
Resolved! COS AP upgrade image in u-boot mode
Hi everyone, I want to learn upgrade image in u-boot mode，but i have some problem about this.Please help me,the problem as blow: 1\how to enter the u-boot mode? Whether we can hit the "ESC" when ap boot? 2\how to upgrade the image int u-boot mode? ...
we have Cisco C9800-L-F-K9 in HA with firwmare version 17.2.5 web browser loading in first page to enter the credentials. after entering credential the next page not loading and stays at white page. what could be the reason. show redundancy every th...
Resolved! Meraki Wifi 802.1x User&Password
Hi,I am trying to set up a new wireless network with 802.1X with a username and password.The network is for 30 students but I don't have everyone's email addresses, is there a way to set up a username and password without an email?Thanks
I’m planning a migration from an existing Cisco Catalyst C9800-L-F-K9 HA pair running IOS-XE 17.12.05 to new Catalyst 9800M hardware. The current setup is with CW9164I & C9120AXI APs, and the target software on the new controllers is IOS-XE 17.15.4b ...
I need urgent help.I have a C9800-40 controller with firmware version ios 17.3.7, with HA SSO. This controller has registered access points models 3700, 3800, and 9120, with external antennas and some with internal antennas.I need to update the firmw...
Resolved! HA License on The Cisco 9800-L
Hello, Is the performance license mandatory to enable HA on the 9800-L? In the datasheet Cisco Catalyst 9800-L Wireless Controller Data Sheet - Cisco it says that: For High Availability deployments, Performance licenses must be brought on both contro...
rebuilt a wireless controller from scratch because the original one was damaged and there was no backup available.I’m currently facing an issue with DHCP. The corporate SSID is working, but clients connected to it are receiving an IP address from the...
Resolved! 9800-40 HA Upgrade from 17.6.4 to 17.9.3
We are upgrading our 9800-40 HA Upgrade from 17.6.4 to 17.9.3. Can these versions be upgraded to directly from and to, or is there version steps?Since this is an HA pair, can these be upgraded one at a time by failing over and upgrading the standby?C...
Resolved! IP MAC Binding and IP Source Guard
Hello everyone, Using IP MAC Binding option in Policy Profile is just about creating a binding table for itself or it can be used as a trusted source for features like IP Source Guard? Thanks
