Hello, i have a WLC 4400 a friend formatted the flash drive with the console of the WLC. i use a Flash drive player in linux and i found 3 linux partitions and all are empty, how can i load the files necessary to the WLC can boot again.thanks
Hello, i have a WLC 4400 a friend formatted the flash drive with the console of the WLC. i use a Flash drive player in linux and i found 3 linux partitions and all are empty, how can i load the files necessary to the WLC can boot again.thanks
I keep getting this message during my day and can't seem to find the problem:WCS has detected one or more alarms of category Switch and severity Major in Virtual Domain rootfor the following items:Radius server '10.26.0.11'(port 1812) is deactivated ...
I have a WLC plugged into a unmanaged 8-port switch which is connected to two interface of cisco router. I also have a DHCP server. I want to create a public SSID to receive IP from one scope and another private SSID to get IP from second scope. does...
I facing a problem that using mac filtering, WPA2/AES/PSK on WLC.When I enable MAC filtering, client cannot connect it.I would like to setup a ssid that support 802.11N, WPA2 key and Mac filtering without radius server.Any people can help?I try the t...
The following is the setup.WLC 4404 running 5.2.178.0 code. 1142N LAPs. ACS ver 3.2 is the radius server and is tied to AD.I tested with three different models of laptops, two worked and one did not. The first laptop that worked: IBM (not on domain) ...
I have WLC2106 with SW 5.2.193.0. I want to configure Local Significant Certificates (LSC)enollment from Microsoft CA based on MS Windows 2008 accordig to cisco guidehttp://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a0080a...
Hi therewe had some problems with audit mismatches on a WCS version 5.0.x; it always said that the apUserName, apPassword and apEnablePassword.Then we upgraded to WCS version 5.2.148 and WLC 5.2.193. The problems with the username and password mismat...
Hi There, Can any has implemented NAC applaice in network while 802.1x is enabled on switch ports.. can they work together..
we have a wireless chip and pin device. It connects using WEP128bit and transactions work fine once its connected. If the C+P device goes into "sleep mode" it finds that when woken up that it cannot find the access point and through its own software ...
platform 1310G. Two AP's setup as follows:LANSW1---AP1===dot1q====AP2---LANSW2I'm looking for an effective way to encrypt data going over the wireless bridged network.Most of the documentation assumes client authentication, however, we are running th...
HelloWe are trying to get controller backups sent to a remote TFTP server via WCS.We have configured the TFTP server IP in WCS via the 'Configure' > 'TFTP Server' section.We then schedule the TFTP via 'Administration' > 'Background Tasks' > 'Controll...
Hi thereis it possible to enable SSH for all LAP's on a WLC console (and even on the GUI)? I only know the command "config ap ssh enable <Cisco AP>", is there a hidden command for all LAP's or a global command to enable SSH per default?Thanks a lot a...
Hi, would like to create a WCS template to disable/enable APs. Does anyone know what existing template to modify or how to create new template? Appreciated.
Hi all,I was wondering does CISCO sell any standalone access-points that supports 802.1x assigned VLAN(s)? Basically I want to create one SSID (ie: GCORP) and have all users connect to that SSID for wireless connectivity. So if Joe connects to GCORP ...
Hello,i need to make sure that a company can surf on one broadband connection from several rooms on 2 different floors, what router and ap i should buy to cover 100m wth regards
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM | ||
| 08-06-2026 09:29 PM |
| User | Count |
|---|---|
| 5 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |