Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Per Cisco Security Advisory ID: cisco-sa-20090727-wlc there appears to a lot of security vulnerabilities. It is recommending that upgrade my controllers to 4.2.207.0 which I have no problems in doing. Question: Would I also need to upgrade my WCS sof...
I have ACS (4.2)1113 series 2003 AD server and 4402 WLCis there any way to integrate all this for single sign on process by adding computer on the ADgroup(wireless) . Note i don't have any certificate server and don't want to use any certificate in t...
Hi,I'd like to know if there is a constrain regarding what models of APs could be used as MAP or RAP in a mesh network. Every AP could be used in this kind of configuration? (for example AIR AP 1130)Thanks
We have a site with one WLC 4400 managing multiple AP1130,connected through Layer 2 D-link switches to Cisco router. We are thinking to have one SSID for internal users (get public IPs from Windows server) and another SSID for external users (using i...
I want to use the Aironet Site Survey Utility in Vista Ultimate 64bit. I have a CB21 card which the utility does detect. It does not show any access points or that the client card is associated.Any help would be greatfully received!Thanks in advance
We have a WLC 4402-12 that support up to 12 AP's. Can I upgrade this WLC to support more then 12 AP's?
I have purchased one AIR-MSE-3310-K9 and 100 hundred wIPS license to support 100 monitor mode AP (AIR-WIPS-AP-100)With the version 5.2, where can i install the license ? into MSE or into WCS?? and how can verify them? I didn't receive any paper licen...
I was reading the data sheet on the 5508 WLCs and was curious about this statement:"Service Port : 10/100/1000 Mbps Ethernet (RJ45) For High Availability for future use"Is this a future design feature so that the 5508s share a common backbone, simila...
WLC 4404 APs1142I have an AP that I dont want to broadcast our SSID but I do want it their. I want it to broadcast only our guest SSID. I have both in a AP group and can see both but is it possible to disable the broadcast for our SSID but not our gu...
We have a centralized NAC server design with a large number of remote sites. With 4.5, I have heard you need Layer 2 adjancency for the WLC's to the NAC servers even if using OOB? Is this correct? This is a serious limitation if so. thanks
We have a 4410n wireless n access point we are using for testing. Have a time getting it to power up with POE and a 3550 switch. I have disabled cpd and spanning tree. Only way to get the AP to power up is remove power from ether port and use DC adap...
Hi There,I have a setup of 9 1522 APs. RAPs=3 and MAPS=6 WLC=4404 Qty 1 (v5.2). All the MAPS have only one hop to nearest RAP. The problem is with one of the MAPs. The MAP shows good signal strength but the client traffic (even ping to controller man...
Hi,I'm looking a wireless site survey planner tool for multi floor office building to estimate the number of APs and location. Not the site survey after install APs.AigMagnet is excellent for single floor but cannot provide multi floor scenario via p...
Is there a way to find out if the AP is under utilize, over utilize or has reached its maximum load? We can see the controller's CPU and memory usage but there are no such reports for Access Points. Because of this, I was wondering if there is a way ...
Hi Folks,Running into an issue upgrading from 4.2.130 to 4.2.207, receiving the following error message and wondering if anyone has run into this same issue and if so what's the fix? Cisco TAC is telling me to reboot the C6500 chassis to resolve it.....
