Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Can I configure data WLAN is central auth/Local Switching and Guest WLAN central auth/Central Switching?Thanks,
The security notes from yesterday are saying that customers with 1510s Mesh APs on 4.1M Mesh code, are recommended to upgrade to 4.2.176.0. If you have 1520s, recommended to upgrade to 5.2.But 4.2.176.0 doesn't support mesh last I heard. So which is ...
After having lots of issues with 5.2.157.0, TAC is suggesting that I use 4.2.176.0. I have 6 production 4404s and 1 test 4402. I have wiped the config on my 4402 and loaded 4.2.176.0 code. I want to test all of my applications before trying to migrat...
Hi NetPro,anyone who has encountered or seen this before ?Error Msg - Two TKIP Michael MIC failures were detected within 0 seconds on Dot11Radio0 interface. The interface will be put on MIC failure hold state for next 60 seconds. Warning Msg - Receiv...
Greetings, im currently looking at applying QoS polices to the access points above only to prioritise voice traffic.<br /><br />We are using 7921 handsets throughout, is it ok just to enable the defaults for voice under "Access Categories" and enable...
Hi, everybody.I have some puzzles with LAP, such as 10201, With a WLC4400 and a DHCP server, is it right there is no need to configurate 1020, it can get IP address with DHCP, and all is automatic, is that right?2, Can I ping or manage 1000 by http o...
Good Morning,i have a simple question. I had a Nokia E series with ICC for Cisco and i have activated the permanent license of this software.If this cell phone is broken, and so i can't release the license from the option of ICC software directly for...
I am trying to migrate my controllers back from 5.2 to 4.2 code. If I have an AP associated to a 5.2 controller, I can change its configuration to point to a 4.2 controller, create an access list so that it can no longer see any of the 5.2 (CAPWAP) c...
I can't find exact information regarding the IPSec checkbox in Security -> AAA -> Radius -> Authentication.On the Cisco Wireless LAN Controller Configuration Guide 5.1, it says "Check the IPSec check box to enable the IP security mechanism, or unchec...
I am looking for advice on how I might optimize performance for the clients in a wireless lab that I have at one of the schools I look after.The classroom is question is located between 2 antonymous 1131AG access points and is not more than 50 feet f...
Hi Every body!Is it possible for sinle "AP" to have ultiple ssids, If yes, then it must effect the performance as " ap" has to send beacon for each ssid then switch the traffic from each ssid.Could anyone explain me this please?thanks a lot!
Hi There, can any body tell me what is the traffic generated by controllers & AP to communicate with WLC. If WLC is across the WAN...what are the traffic consideration one should take care..
I am trying to install an 1100 series AP, it gets a IP addres from DHCP. when I try to get to that IP address from the web to configure the AP, it will not connect. What am I doing wrong?
<p>My problem is to get an IP with the WLAN-Clients. They could connect but didn't become a dhcp-lease.</p><p>I've looked in all the other posts for dhcp, but couldnt locate my problem.</p><p>Any help is welcome. Config is attached.</p>
Hi Guys, Does anyone here have an idea what does it mean? I am using Wireless LAN controller. Thanks in advance.Cheers!
