We are having an issue where the guest portal is not bringing up the redirect page for authentication. We are using a Cisco WLC 5500 and use ISE version2.4.0.357 patch 8,11. On this issue, the AP in question is part of a flexconnect group with other ...
Forum Posts
Resolved! Is it possible to retrieve a comprehensive list of all wireless devices with a specific policy?
We use a specific group policy to allow VIP devices to connect to our guest wireless networks without going through the SMS/Splash sign-in.Is it possible to retrieve a comprehensive list of every client with this policy applied, for audit and clean-u...
hello I'm trying to access the AP after setting up, but I can't. Is it possible to do log analysis? ap->radius server Ping communication is possible. ID/PW is also correct. When I try to connect to ssid on my device, I can't connect and the logs are ...
I have a WLAN configured and in the radio policy section, I am getting the message "although enabled, the WLAN is not operational on 6GHZ Radios due to one or more missing required configuration (WPA2 disabled, WPA3 and Dot 11ax enabled) (see the att...
Dear All,I would like to test a anchor mobility with 5508 and 9800.Both controller can ping and reach other.But status keep show "Control Path Down".For 9800 is using 17.3.2a version and 5508 is 8.5.164.216.I tried to reboot those controller but stil...
I've been trying to setup a virtual 9800 to support LDAP for one of the SSIDs but haven't had success. I followed the instructions here: Configure Catalyst 9800 WLC with LDAP Authentication for 802.1X and Web-auth - Cisco and as far as I can tell ...
Listen here: S11|E6 Bridging the Gap: Cisco Catalyst CW9163E- The Ultimate Outdoor Wi-Fi 6E Solution In this episode, we're spotlighting the Cisco Catalyst™ CW9163E, a remarkable outdoor Wi-Fi 6E access point that's built to withstand even the harshe...
I logged into the console of the Controller AP and show version got me this result:I recently upgraded from 8.3.133 to 8.10.185 but when it finished, the controller AP did not show up as an access point, which was previously shown when I was still in...
Hi, (it's better to say hello). Here's my problem On AP in root mode etc... On AP in repeater mode etc...here's the AP root configuration dot11 ssid WLAN_***authentication open eap eap_methods authentication network-eap eap_methods authentication k...
Hi Everyone, I have a client that will be split in two differents entities with two differents LAN. But it will remains hybrid site with hybrid meeting room that will be used by employees from entity A and employees from entity B. So they want to imp...
Tenemos un AIR-AP2802I-A-K9 con el siguiente error en bucle:[*01/01/1970 00:00:21.3745][*01/01/1970 00:00:21.3745] (write)Unable to open I2C device interface (/dev/act2) for ACT2 (file = -1)[*01/01/1970 00:00:21.3749][*01/01/1970 00:00:21.3749] (ACT2...
Hi, I'm currently using the following AP to read historical data for signal quality for of my APsnetworks/{networkId}/wireless/signalQualityHistory I'm attempting to read timespan of 8h back from current time in a resolution of 300 secs (making a cal...
Hello, We have 2 APs in one site and both connected to the same switch. Both APs are currently flapping and disconnecting. Internet service appears to be fine. Please assist
Hi,just want to know, it can combine the new access point to existing dashboard, i mean now we already have 3 access point on 1 dashboard, next month we want to buy another access point, but this is on different location.It can be combine the new acc...
I have set up Configuring RADIUS Authentication with WPA2-Enterprise. My AP management IP for MR55-1-Downstairs-AP is configured. USER VLAN ID for this which set up in attribute is 129 - the user who connects to this AP should get an IP that is not m...
