Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I have 2 4402 WLC's (IOS 5.0.148.2) that support a mix of 1242 and 1200 LAPs. I use DHCP option 43 for the initial location of the WLC's. The problem I have is when I test failover by shutting off the primary controller, all the 1242 APs failover to ...
Kindly advise what part number of 1300 Series bridge should I order to have maximum 100 mW power output in .11b mode. I intend to use external antennas.
Hi,i need some clarifications regarding configuring Aironet stand-alone AP (in this case AIR-LAP1131AG).Under Security->SSID Manager:what is the purpose of Network ID?Under Guest Mode/Infrastructure SSID Settings - what is the purpose of Set Infrastr...
I do have a outdoor mesh AP 1522. This is not joining to WLC 2100. Need help on this...Plz find the error mesage:=============================================AP0021.56e4.5e00>enPassword: *Nov 3 10:20:10.467: LWAPP_CLIENT_ERROR_DEBUG: Retransmission c...
Hi,I have one branch,100m away from my HQ. Hq is equiped with cisco devices.There is no cabling in brach office. How can i connect any 1 floor of my branch to my HQ using cisco wifi devices with maximum range???
I'm noticing in WCS 5.1.64.0 that I can set a exclusion area, and the planner will put a AP in that area. Does planner not pay attention to exclusion areas?
My customer has a wireless solution with WLC526 and LAP521. Is possible add a NAC solution (Clean Access)? Regards. Mirko Severi.
HiDoes both do Guest authentication?If Cisco Wireless LAN Solution Engine (WLSE) can do Guest, Does it require other devices to work with it? or standalone?If Cisco Wireless Control System (WCS) can do Guest, Does it require other devices to work wit...
I'm securing my guest WLAN and have WLC ACL's in place and the network is segmented from everything else but I decided to run a port scan against the virtual WLC interface (1.1.1.1 for me) and ports 25 and 110 are listening. I connected to 25 and it ...
Implementing PGP whole disk encryption of laptops with Aironet CB21AG nics and LEAP configuration. Configured to pass login (AD) credentials from PGP login thru to Windows.Will not pass thru AD credentials at login until LEAP config removed. Has anyo...
Hi AllHaving installed a WLC 526 for a small school I have assumed that the ports were similar to those on the 2100 etc. However whenever port 2 is cabled the WLC dies.The setup is a flat layer 2 domain WLC with 5 aps connected. All connected via a l...
Hi,I can't get my 871w to enable WPA2 for it. I found a reference to "wpa version 2" as CLI which my rather new IOS doesn't seem to understand. So how to enable WPA2 via CLI commands? And by the way do you have a link to the wireless CLI reference?Ci...
Hello,I heard from a Cisco SE that WLCs could not manage the same number of APs if these are 802.11n APs (1250) or others.For example: a WLC4404-50 will manage 50 802.11a/b/g APs but only about 33 802.11n APs (1250).Is that true ? I really can't find...
Hi,Apologies if this is posted in the wrong discussion/forum thread.I have a Aironet 1242AG Wireless Access Point configured in Workgroup Bridge mode. The Access Point associates successfully using WPA-PSK to the existing SSID that we have here. I am...
Hi all,I have tried using access control list to block certain IPs from accessing WLC web management. I apply the ACL to interface management, but it seems like no effect at all.How can I block or permit some IPs so only certain IPs can access WLC we...
