Wireless

When we go to upload the newest version onto the controller, we get an error. "Unable to load to flash". I am guessing this is a piece of bad memory.

Is it possible to upgrade the Aironet 1200 series APs to the LWAPP firmware (c1200-rcvk9w8-tar.123-7.JX), WITHOUT a WLAN controller connected ? I have tried this and the hash key is not generated in the AP config file, this file is needed to add the ...

The problem is, if the card is inserted in the slot and the acu software v.6.6 (or older) is installed, the card is via the ACU software not able to associate to a cisco accesspoint. How can I solve this problem?I 've tried several ways with win 2000...

I have tried ip access-list extended with "log" option. Filtering works well but nothing is logged. My AP is AIR-AP1242AG-E-K9 IOS Version 12.3(7)JA1What could be wrong?

Hello,I have about 60 AP350 VXworks deployed. 350 series clients connect and authenticate via EAP-TLS. Those of them which are heavily in use reboot ccasionally. I do not have any hint why, of course the logs are purged at reboot. There is no regular...

Hi,We have purchased cisco linksys WRT54G device. We are interested to know how many wireless users can connect to this device. (like these many g users, b users, a users)Regardsskrao

Hi there. I am trying to find out exactly how rogue detection works on the airespace product but am having no luck. I understand that I need a dedicated AP for this, but I get confused when I hear that the AP doesnt need to be within RF range of the ...

Have installed a Verisign class 3 certificate on ACS 3.3 in order to provide Peap authentication on Wireless client. If we view the certificate when the Wireless client authenticate to ACS, it show the Verisign Intermediate certificate has expired (0...

I try to upgrade a WS-SVC-WISM-1-K9 from 3.2.116.21 to 4.0.155.0 (SWISMK9-4-0-155-0.aes)which fail with this error:Tue Jun 13 14:36:41 2006: tftp rc=0, pHost=1.2.3.4 pFilename=wifi/SWISMK9-4-0-155-0.aes pLocalFilename=/mnt/download/local.tgzTue J...

We have a number of AP350s which we're upgrading from VxWorks to IOS. The conversion to IOS works fine but when I try and upgrade to a later version of IOS frequently the dot11radio0 interface disappears after the upgrade. On one AP the interface cam...

I have two root bridges - A & B - and I have one non root bridge - Z. The bridges A & B are broadcasting the same SSIDs and so Z can associate to either of them. The directional antennas, line of sight and everything has been set so that Z would obvi...

If I currently have an 802.11g network that has been optimized to support data devices at 36 Mb/s or higher (i.e., AP cells a little closer to maintain higher speeds) and I now want to add 7920 wireless phone support, do I have to re-do my site surve...

I am not sure if this is the correct place to ask the following questions, but here it goes...As part of a wireless pilot project we have installed 50 access points (Cisco aironet 1231G) in a couple of buildings. The real project once approved could ...

I am setting a wireless interconnection. In the Head Office I have a Cisco 1310 root Bridge and in the remote office I have the Cisco 1310 acting as the bridge. My question is - Could I directly connect the Cisco Access Point to the Cisco Aironet Po...

Hi,We have to implement wireless lan with WRT5RG devices.We have the reason to use only this model.Our question is how much area one accesspoint can cover. Based on that we will decide how many access points we have to purchase?Regardsskrao