Hi All,I would like to configure my 1200 aironet AP from the console. When I power on the AP, I can not get the prompt ">". Instead I get "Auto so forth and so on".how do i get to the user mode?Thanks,paul
Hi All,I would like to configure my 1200 aironet AP from the console. When I power on the AP, I can not get the prompt ">". Instead I get "Auto so forth and so on".how do i get to the user mode?Thanks,paul
In a design with 2 redundant contollers in the head quarter and small remote sites connected via a WAN link and equipped with AP1030 without controllers, is there a way to configure the AP1030 that the data payload will remain at the remote site not ...
I have heard that there will be a new IOS that will work with the Airespace controllers. I thought I heard that only be for the 1230s and 1130s would be capable of this, but I wanted to clarification.
I have great problem with LMC352 card in my laptop. I`ve just bought MSI Megabook 510C. I`ve pluged in the card, windows had recognized new hardware etc... Everything`s great but Windows doesn`t see wireless connection. Troubleshoot says that card do...
We have a 1400 bridge located on a radio tower. Three times it has been damaged by lightning and we have had to replace the unit. There is no physical evidence of it being struck directly, but all three times it quit was during a storm.We are using t...
We are trying to use the "Device Specific Configuration" feature to assign <hostname> & IP Address to AP's. Has anyone had experience using this feature? We receive various error messages relating to login and invalid command although the login and...
When I login to a AP from my bowser and get to the home page, click on the link clients under ASSOCIATION it gives me the Device type.Does anyone know what the Device type of a 4500-radio is or 4800-radio?Most of the devices are showing up as unknown...
Hi, I've noticed that when I do a show dot11 associaciotions "mac-address" I receive the following output for a 350 Series Card with a 5.60.xx firmware:Device : 350-client Software Version : 5.60CCX Version : NONEBy downgradi...
Hello,I have problems with connecting my 7920 wireless ip phone and my laptop via the connection utility tool.I did some testing again and i could install the USB driver correctly appearantly.What i see is that it creates a seperate network...
I'm considering to configure a wireless link (about 1,5Km) for VoIP use. Which is the bandwidth required for this use?Thanks
Hi, I have 4 WDS-APs that were working fine with my WLSE. I use local radius on the APs for WLSE authentication. I just upgraded all 4 APs to 12.3(4)JA1 and now the WLSE cannot connect to them. I'm running wlse2.11FCS......any suggestions?...than...
I try to authenticate a 1300 Worgroup bridge with EAP-FAST. Using ACS 3.3(2) Build 2 and 1231 AP's with WDS.Is there anyone who has tried this configuration. Ordinary wireless clients are OK.
Hello,Do anybody know if it possible to put/attach additional information file(s) to every site in Location Manager?At the moment I just found out the only string in "Floor" properities for any coments. But I can't put there enough information in rea...
I would like to know what is involved/required to setup authentication for wireless clients where they can simply connect to an open Cisco wireless AP, but have to authenticate in their web browser prior to getting access to the network. I am basica...
I get this message when I am adding more devices after discovery. I have the WLSE 1130 that I just upgraded to 2.12fcs. Need help ASAP.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-27-2025 06:05 AM | ||
02-18-2025 11:22 AM | ||
02-13-2025 10:43 PM | ||
02-13-2025 08:57 PM | ||
02-04-2025 03:06 AM |
User | Count |
---|---|
10 | |
8 | |
3 | |
1 | |
1 |