Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi experts, I know the way to change the IP state on "general-IP Config", but my query is that can we do that for all the APs on WLC together?I have hundreds of APs. Additionally, the DHCP server is in Linux server, not on the WLC. Thanks in advance...
Hi all, We have an issue with a customer on which we have deploy our captive portal solution. They have a Cisco WLC C9800-CL with AP in flexconnect mode. Users are seeing a 403 error message when they are being redirected to our splash page. One of o...
HI everyone My network environment is shown in the following picture，I looked into some loggs on my WLC 9800 and saw a bunch of loggs like this:%SWPORT-4-MAC_CONFLICT: Dynamic mac XXXX.XXXX.XXXX from Port-channel2 conflict with WlClient, please chec...
Hi, we have 1x pair foreign wireless controllers and 1x pair anchor wireless controllers. But can't login to anchor wlc standby unit, is it normal? how can access (ssh) anchor wlc standby unit? Can anyone please advise, thanks in advance!
I am in a new network that has AP switch port configured as Trunk ports with the native vlan tagged. I have always read to have them set as access port with the vlan set. Is there any benefit to either of these options. I do like looking in switches ...
Hello Team,We have two 9800 wlc running on 17.9.2 , both the wlc's are running in active standby mode.These wlc are installed in VM two different clusters.Please suggest best practise to reload asecondary node of the wlc.(our requirement the VM teams...
I am looking for some guidance on how to configure Cisco 1852AP with Mobility Express 8.10.185.0. I want to use MAC filtering with Radius server (MS Network Policy Server) for authentication and authorization. I have searched online but I could not f...
- FYI : https://www.wi-fi.org/news-events/newsroom/wi-fi-alliance-introduces-wi-fi-certified-7 M.
I'm trying to adjust the TX power on my access points so clients get connected to the closes AP when they move and do not get stuck to a single one. I adjusted the TX power using a RF Profile between 8 - 14 dBm, but after a while I still see some of ...
Resolved! Firmware Network Issue MR30.5
Hi together,we have a bad condition with MR 29.6.1 → MR 30.5 on AP MR36 ....Let's try to describe:We have 100 AP's, MR33, 36, 55 ...In some classrooms we didn't have enough RJ-45 plug near the beamer/projector, so we had used network Splitter. (1)Thi...
Hi,I have "Failed Authentication" with this client: da:0e:xx:yy:zz:aeA pcap file indicated a bad AP which try to reply: e6:cb:bc:ff:gg:hh but this bad AP mac address is not in a rogue AP list.My legitimate AP has this MAC address: e0:cb:bc:ff:gg:hhHo...
Dear Cisco Support Team, I hope this message finds you well. My name is Kashif, and I am currently working on configuring the Cisco AIR-CAP3602I-N-K9 device for our network infrastructure. I am reaching out to seek your expert guidance and assistance...
Resolved! l have AP-2802i-e-k9 l need configure
Hi l have alot of cisco AP-2802i-e-k9 l want configure then without controller and l want also setup wpa3 enterprise it is possible???
I HAVE AN IPAD FOR THE SELLERS IN MY STORE, I CREATE A HIDDEN SSID FOR THEM TO CONNECT BUT EVERY THEY ADD IT THEY LOG IN WITHOUT PROBLEM, THE PROBLEM IS THAT WHEN IT IS TURNED OFF AND ON AGAIN IT NO LONGER CONNECTS AUTOMATICALLY AND I HAVE TO ADD EVE...
Resolved! WLC 4402 question
We have a WLC 4402 and I want to know if I can reboot all my AP's without going to touch each one at each site? I see an option under the Wireless tab, click on an AP then I see "Perform a hardware reset on this AP" will this just simply reboot the A...
