Wireless

How do I configure a Cisco 1242 WAP if I do not have a Wireless Access Controller. The unit has recieved a DHCP address from my network, but I cannot telnet nor web into the device. The Cisco getting started guide says that you can revert it to auton...

Hello.IEEE802.11,1999 Edition standart define reason code 0x8 - Disassociated because sending station is leaving (or has left) BSSBut what exactly it mean?For example there are two station AP1(non root) & AP2(root), on AP2 in log we see "Interface Do...

Anyone using QoS to regulate use of resources consumed by guest users? Any rules of thumb/guidelines/examples?

How do ACL's work on the WLC?I am using 4.X ver of software for the WLC with LWAPP APs, like there is any other way.I have a guest VLAN setup and when I apply an ACL to it, it stops responding. I would think that that ACLs work like ACLs, but that is...

Hi there,for testing purposes, I would like to force an Aironet 1230 AP to SENDwith a specific WLAN data rate (say 48 MBit/s). Unfortunately, I amunable to do that.A Linksys AP for example is able to to do it. Its webinterface has anattribute "Tx Rat...

I am having trouble with a CAS/CAM configuration. I have been testing a guest tunnel configuration with 2 cisco wireless lan controllers in the past. That has worked when I used a firewall on a PC, with 2 NIC's to forward traffic for the guest tunnel...

Dear all,I've configured our new AP and encountered the following problem.When people from other offices come to my office and try to connect to my ap they pick up the wireless network but they don't get an ip address in our range.I can't find out wh...

Hi everybody.We are using Catalyst Express switches and air-1121G for a wlan network covering a hotel. When we set the smartport-setting on switch to "access-point" users cannot move from one access-point to another. Setting the smartport-role to "ot...

Hi Sir,I would like to use Radius-based Vlan access control through WLAN as the number of SSID map to wired VLAN is limited to only 16. I have an ACS 4.0 But i wish to use AD to manage my user profile. How can I set the following to enable Radius-bas...

HiI have a test enviroment with 2 ap1030 and i want to make a 5ghz bridge link with these two aps. this should be possilbe. but im not able to get it worked. i also didnt found a good documenation for this configuration.do i need to make both aps in ...

Hello allI'm the wireless admin of a high school.We have around 60 AP1230 b/g here and a WLSE. The APs are splitted into two IP subnet where in each is a WDS.The network is open and isn't using any authorisation or encryption.The authorisation is don...

Hi GuysI have been struggling for a week now trying to get wireless working on my Cisco 877W. All the other functions are fine, DSL, VPNs, FW, but I cannot get the wireless to work at all.The configuration is very confusing, and I even resorted to us...

Hi,When a 1000 series AP connects to the LAN, it can get association to the 4400 controller automatically. Can I allow only some APs associate to the controller? When some one connects an AP to the LAN, this AP can't be brought up.Thanks,yytellmey

Hi,I would like to ask if i installed a 900Mhz cordless phone would it still interfere with my Cisco AP 1231G? though, i did not test our cordless phone, but i turned it off as i operates in 2.4GHz frequencyThanks,Eduard

I am new to these 2 terms.What's the main difference between autonomous and LWAPP access point?Autonomous AP can work on it's own, while LWAPP need to be used with WNC?If I need to deploy an wireless enironment, I should use LWAPP, right?