How to configuree separate dedicated channel for Voice and Data on same Physical Link
How to configuree separate dedicated channel for Voice and Data on same Physical Link
We have a customer WLAN comprising a 350 Bridge with an omni antenna connecting to an AP1200. The customer wants to run 7920 IP mobiles roaming between the 350 and the 12000. The 350 is set to be a "Root Bridge" and the AP1200 associates with it fine...
We are using Cisco 1200 AP's(802.11b). If I had an area where there is channel overlap, how would I know that it does exits? Is there certain errors to look at on the AP's? I don't see anything in the log to reflect that it could be occuring.
I have all my wired network devices on vlan 1. I'm almost out of addresses on this subnet. So I would like to put my APs in a different vlan using a different address range. If I make the vlan my AP are in native can they still talk to wired devic...
Is ther a way to improve strong security between two wireless bridges 1400 without use of a RADIUS server?Thanks,Ronaldo.
I have 2 aironet 1100, one of which is associated with the other as a standby. The standby disassociates itself from the active access point when the wait for poll timer elapses, this also takes the radio down. This seems to be from a virtual interfa...
I want to configure the WEP or other security mode on thin clients - they can't operate on graphical mode.I've tried the Cisco tools all works fine but on X environment - I can't configure or start the WEP without X. I've tried "standard" linux tools...
dear all who can tell me the polarization of cisco antenna ,when I see the training book gived by cisco,it is vertical,but in fact it is vertical and horizontal,who can tell me the right answer? thanks a lot
Hi, i'm looking for a device to point Dish antennas.We need an HW that help us to see if antennas are correct pointed, like a signal generator but at very low-low cost. Does anyone can help us in this research ?Thanks
I just recieved my 1400 bridges, and was surprised when they had a dual coax feed from the power injector. I was lead to believe that it would take a cat5 cable. It shipped with both a 20' and a 50' cable that you can connect with a grouding couple...
I'm having a hard time understanding what WDS is and whether I should enable it or not. I've read the documentation, but I don't understand if this is just for Cisco devices (clients and APs). I think I need it if I want to take advantage of rouge ...
I've installed the latest and greatest WLSE 2.5 and am starting to upgrade our 340 AP's to 1210's running 12.2(13)JA.350 Series Clients running ACU 6.2 are associated and key management is CCKM allowing Fast Roaming. The "Enable Radio Management Sup...
I have 1 Root Bridge 350 connecting to 3 non-root bridge 350s - all within 500 feet. Connections hang and I can wake up sometimes by tracert. All units have the same problem. They have all been configured with quick setup. Take 340s - also configured...
I have a WGB352 associated to a BR350 in AP mode. The problem is, when I am looking at the association table on the BR350, it says the WGB is a repeater and its parent is [self]. How can I fix this so it will work as the client?
Can a 7920 be used with a 802.11g only Access-Point ?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-17-2025 07:07 PM | ||
04-17-2025 11:18 AM | ||
04-17-2025 03:05 AM | ||
02-27-2025 06:05 AM | ||
02-18-2025 11:22 AM |
User | Count |
---|---|
31 | |
7 | |
5 | |
3 | |
3 |