Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Bookmark
|
Subscribe
|

Labels

Forum Posts

I have two conference rooms that need to have wireless access. In between the conference rooms, which are about 100ft apart, there is a "Radioactive Materials" room. Will there be interference caused by the the radioactive materilas room, like the in...

c.tenley by Level 1
  • 475 Views
  • 3 replies
  • 0 Helpful votes

Does anyone have any suggestions for allowing temporary profiles to be created by end-users?Currently we are using the Cisco ACU software to control the wireless configuration on our laptops, but this is "hidden" from end users (they are unaware of t...

Hello,I have a 350 client pcmcia card with the latest ACU, NDIS, Firmware the is associating between two AP's. One is a 1200 (12.02) with the better signal and the other is a 350 (12.02) weaker signal. The client is not associating with the stonger...

tlchant by Level 1
  • 410 Views
  • 1 replies
  • 0 Helpful votes

hello , I have purchased 2 aironet 1220 , (upgraded to IOS ) AP's & a few 350 PCMCIA cards , I was hoping to set up WPA , sadly the although the AP is WPA ready the APU for the 350 PCMCIA cards do not support it yet.I want to make the wireless ne...

Can I use the radius server that comes with Windows2000 server in the Internet Authentication Service with the Aironet 1200 for authentication? Or do I need to use Secure Access Server or something like it?

jmackin by Level 1
  • 444 Views
  • 1 replies
  • 0 Helpful votes

. On Cisco Aironet Wireless Bridges – can we limit the CPE to Wireless Bridge Connection in Bandwidth? E.g. 128kbps, (instead of the 802.11x 1,2,5.5,11Mbps data rates). If not, then how can we achieve bandwidth control, since we wish to optimiz...

Dear all The 802.11 standard does not require that the Access Point broadcast the Service Set ID. This phrase is right or wrong I see the document which said we can set ,can you tell me answerthanks a lot

admin_2 by Level 3
  • 341 Views
  • 1 replies
  • 0 Helpful votes

I am using the Cisco 350 card in an office environment, but my signal level is "very low" or "low" now at all times. I use a Dell CPiA laptop that, until a few days ago, always registered a "very good" or "excellent" signal strength.The laptop is a...

jtalens by Level 1
  • 697 Views
  • 5 replies
  • 0 Helpful votes

I have worked with home wlan devices (dhcp/router/switch ie. SMC/Netgear/Linksys,etc.)), but am now venturing out to small businesses.I have a small rural medical clinic that is pursuing an online med package and needs wireless access to their existi...

wpcc by Level 1
  • 453 Views
  • 1 replies
  • 0 Helpful votes

We are setting up a conference room with three access points(1200's). All three are set up using different channels(1,6 or 11). When we were doing some testing with 25 computers we noticed that whichever access point was directed to channel 11, tha...

rx33328 by Level 1
  • 587 Views
  • 3 replies
  • 0 Helpful votes

I was told it´s possible to configure a trunk beetween 2 parallel BR350 links working on different channels which are connected to a switch on both sides.My question now is if it´s possible to configure the same when one link is a 3rd party transpare...

t.franke by Level 1
  • 386 Views
  • 1 replies
  • 0 Helpful votes

I'm having some trouble here, maybe it's lack of understanding or maybe I'm just a tool and am doing something dumb.Am I wrong in assuming that if I setup VLANs on an AP350 and map a simple WEP secured SSID to each VLAN, each of those SSIDs will beco...

jason by Level 1
  • 513 Views
  • 1 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card