Currently I have set my AP 1200 to use WEP. Have been reading far too many discussions that state this is not secure. What is the best/highest security that I can change the AP 1200 to. Thanks in advance.
Currently I have set my AP 1200 to use WEP. Have been reading far too many discussions that state this is not secure. What is the best/highest security that I can change the AP 1200 to. Thanks in advance.
I want my 2006 to be the DHCP server. Nothing pulls an address even though I have built and enabled a scope. I am using the GUI interface. Any ideas???
Hi allWe are running AP1200 with open eap. We are experiencing a transient problem with a couple unknown PC's attempting (and Failing) authentication every second. After some time, the memory gets fragmented on the AP, causing the AP to hang.From the...
Hi, I am having a little issue of the Linksys wireless printe server associating with my AP1231. I have 2 vlans on my AP one using WPA and the other open for printing. My wireless print network will have static ip address, I have local dhcp server on...
I am out of .....I have to AP 1210, one is the WDS master, the second one is a WDS client. The client AP is registered in the master. But houw must i configure the client AP? i am running two vlan's on the master.What to configure on the client? Same...
Hi,Does Cisco Aironet 340 supports Power over Ethernet?Thank you.Regards,Ron
I am converting from Aironet 1231 APs to Cisco 1010 LWAPP APs in the near future. My question is will the power injectors that I am using with the 1231s (AIR-PWRINJ3) work with the Cisco 1010 APs? Voltage requirements appear to be the same according ...
Is it possible infrastructure authentication with funk LEAP server instead of ACS?
Is it possible to setup the Aironet 1100 so that both WEP-128 and WPA run at the same time?
I am out of .....I have to AP 1210, one is the WDS master, the second one is a WDS client. The client AP is registered in the master. But houw must i configure the client AP? i am running two vlan's on the master.What to configure on the client? Same...
I am interested in creating a guest internet WLAN using LWAPP AP 1010s and the Cisco BBSM. Are there any issues that I should be aware of or are the AP1010s compatible with the BBSM? I have attached a high-level diagram of what I am proposing.Thanks,...
Could you please help me out with the details of the Aironet 1310 AP/bridge..a.) Make CISCOb.) Model AIR-BR1310G-A-K9c.) Freq Range 2400-2483.5d.) Freq Control ________________e.) Rated Power ________________ f.) BW&Emission ________________ g.) Cond...
Hello,Is it possible to utilize EAP with Active Directory + Radius Win2K without the use of ACS or a CA? Can I manually install the required certs to make this happen?
I am going to order "AIR-AP1231G-E-K9", and it requires external antennas. I need antennas directlty connected with this AP without any cable. Is "AIR-ANT4941" correct antinna for this requirement. If it is correct selection, do i need to order two "...
Greetings,I'm fairly new to all things Cisco. I've purchased two Cisco 1310 bridges and, for the life of me, cannot figure out where I can download the latest IOS for the Bridges. Can anyone point me to a link that actually works? Is there some secre...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-17-2026 11:43 AM | ||
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM |
| User | Count |
|---|---|
| 4 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |