Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Dear MembersCan i connect two PCI WLAN 350 adapter cards in adhoc mode to connect just two PCs. is there some problem in this ?what is rf output power of aironet 350 client adapter cards ?regards
I have set up VLANs on my Aironet 1200s in my test lab, and have got them to work successfully. I have also been able to use a VPN connection to gain network access on the open VLAN. My question is while using the VPN client,(1) will roaming be aff...
Has anyone sucessfully implemented Dynamic VLAN assigment. I have not been sucessful. I am using at IOS Based 1200 with ACS 3.2. I am using PEAP as the authentication mechanism and I have tried both SSID assignment and VLAN assignment VIA RADIUS and ...
Hi All,I am in the process of updating my AP1200 from ver. 12.01T1. I will be using LEAP and vlans. Would you recommend I stick with VXWorks or should I move to the latests version of IOS? Thanks,
We have currently purchased a test laptop with the new intel 2100 card that "supports LEAP" Intel Is telling me that drivers must be obtained from Cisco. I have tried teh ACU which obviously does not work being it is not an aironet card. Anyone t...
Resolved! 7920 Wireless Phones
I have several access points in one location. I set the maximum number of associations for my wireless voice VLAN to 5. After 5 associations, the 1200 will not take more....that's what I want to insure quality.But, how can I force a phone to skip t...
I want to use wireless to bridge a long distance in my plant instead of using fiber. Can I use a 1200 AP to do this or do I need a 1400?Thanks!
Is there an approved amplifier for the Aironet 1200 ?My current setup is as followsAironet 1200 @ 100mW30ft of LMR 40015 dbi omni AntennaI want to extend my PCMCIA roaming range to a diameter of 1000ft and am having no luck... can you help me?Thanks
After upgrading th AP1200 to IOS with the conversion image the unit fails to start, when conencting a terminal to the consoleport you got this message:Testing DRAM...(press <esc> to bypass)DRAM OKPower-on reset.Copyright 1996-2000 Cisco Systems, Inc....
What are acceptable values for the "Carrier Busy" and "Noise Value" when performing the carrier test on a 350 bridge?For Carrier Busy, I'm getting 10% max across all channelsFor Noise Value, I'm getting -83dBm max across all channels
I have 1200 series access points running VxWorks 12.03T. I have the LAN version of Ciscoworks2000 (assume latest version). The ANI server in Ciscoworks discovers the APs but doesn't recognize them (they show up as unknown). Can the LAN version of ...
I am having a problem pinging any wireless clients. They associate, DHCP fine and can access hosts on the wired side. However, from the router or any wired device in the same vlan as the wireless device, I get no replies from the ping. This had wo...
Is it possible to map an SSID with a Group on the Tacacs server ?I've differents SSID (and VLAN) on my AP1200 with MAC-address authentication, and I would like to authorized a MAC only for thi SSID with a ACS group.SSID "A" with MAC "A"SSID "B" with ...
what is the best way for a wireless survey for 7920 ip phone?i have a Wlan with 3 AP350 and 3 AP1100, and 10 7920phone.i have many doubts about the "roaming" ....thanks
I will have to design a wlan for a supermarket. Any idea if I can design a wireless lan without using a hub or switch?
