Wireless

Is there a safe way to change the duplex (from half to full) on the wired port of a 1200 AP running IOS 12.3? When I go into it wirelessly with a browser I see a message that says I shouldn't change the duplex setting.Can I do it via telnet or WLSE?

Hi,I currently have Cisco 1100 AP's in my network normally used by wireless users for non voice applications. The AP's are running IOS 12.3(4)JA.I have bought a couple 7920 phones as a trial for voice over the wireless. The phones are running firmwar...

I just tried to upgrade my firmware to IOS in the AP1200, using the steps provided by the Cisco website. And now i can't access the AP using IE and the IP address. I used to be able to access it fine when I had VxWorks, but since the upgrade I cannot...

One of our offices is serviced by a single 1200 AP. It in the far areas of our office, we had seen the signal drop off. Does Cisco make some type of Signal booster or repeater?Basically I dont want to buy another 1200 if it means they will get droppe...

I have a few Aironet 1200's running 12.2(11)JA3 with WVLAN'ing. Users on one of the WVLANs complain that more than one wifi client cannot associate at a time. If the currently associated client signs off, the next one is immediately able to get on.LE...

Hi,I'm trying to get a kit together that can do all needed site surveys. I know the 1200 will work fine for indoor AP surveys, but can it also be used instead of a 1310 for all outdoor site surveys? Is it functionally the same in terms of radio stren...

In release 5.2 you could use BBSD to backup and restore the configuration of the BBSM.But for BBSD 5.3 http://www.cisco.com/en/US/products/sw/netmgtsw/ps533/products_user_guide_chapter09186a0080208b3f.htmlit says that:For the 5.3 release, all BBSM ba...

We have a large network with AP350, and those do not support Layer 3 roaming.I would like to know what is different in latency and functionality between Layer 2 and 3?There is mentioned a WLSE in the Layer 3 design, but is it needed?We are about to b...

We are currently using a 1200 series access point in workgroup bridge mode, 1200 access points and a 2955 switch. All of our devices have the latest IOS. The 1200 workgroup bridge will be located in a slow moving machine(around 20 km/h)and we are try...

Dear All,Pls kindly suggest the suitable antenna to be used for the Aironet AP AIR-AP1231G-E-K9 installed for the guest room Net access.I took the survey with only 1100 series access points that covers only 4 rooms if ap is kept in the center of the ...

Does anyone know how to manually convert mW to dbm? Thank you.

Hi,I have an application that installd with br350 that configure to br NON ROOT, this application must to have very fast roaming with the server in the root network with no timeout at all.when the roaming begins I have about 1sec with timeout.Someone...

I am trying to install a Cisco Aironet 1100 access point, but I cannot connect and there are three flashing amber lights. I have seen post about three steady amber lights, but what does it mean if they are flashing?Many thanksMark

I am preparing for the equipments that I am going to use in setting a wireless bridge. Could you please help me out what are the other things that I do need and don't need?Here is the list:2 units eachAIR-BR1310G-A-K9-R Aironet 1310 Outdoor AP/BR w/R...

I have a cisco 802.11a/b/g client using leap and mac authentication. When I check the acs logs, there is a Re-key entry every 1 or 2 minutes apart. Also, Authen ok entries. I have broadcast key rotation and reauthentication set at 600 seconds. I cant...