Wireless

Hi,I'm using an IAS server as my authentication server.I have also an WLSE 2.9, i have configured an AP to be WDS , following the config guide.WDS information state is ACTIVE but in wds registration i can't see this AP registed.In wireless network in...

Can anybody explain why the Black Hole Mitigation feature changes the default 100kmicrosec beacon interval to a "slightly lower value" (usually 99 or 98 kmicrosec) ? I am rather baffled by this very slight change - where is the advantage to black hol...

A company we are working with has Cisco 1200 WAP's that are conneced to Cisco 3550 switches at 100MB and are using VLANS on these WAP's to accomodate voice and data.My questions are:1. Does this require that the connection between the switch and the ...

WLSE 2.9.1a.When I use the option "overwrite" then the wlse send the configuration into the startup-configuration and force the AP to reload.But when I use the option "no overwrite" then the wlse do exaclty the same as with "overwrite", instead to me...

HELPCan some one send me a copy of a config that uses PEAP and Microsoft IAS. I wan the AP and the clients authenticate to the IAS.ALso, if you do not mind show me an example of a client card configurationThank youCristian [email protected]

Hi,A customer of mine decided not to use CiscoSecure ACS. They want to just use Windows 2000 IAS/Radius and certificate server for authentication.They do have a few windows 2000 desktops (and some '98). I know that only XP supports PEAP inhearantly.H...

Hi! I discovered the unusual trouble with the HTTP serever Access Point Aironet 1200.The trouble consists of the unability to connect to the HTTP-server if I use any network address except 192.168.0.0.In case of using 192.168.0.0 everything is all ri...

Hi,Is there a way to display signal strength of clients within the range of 1200 AP (including those that are not connected) ?"sh dot11 associations all-clients" only display the connected clients.Would appreciate if someone can help. Thxs.

The AP documentation states that MIC is included in TKIP. However, my client cards report that MIC is not being used. I am wondering which is true?

Hi,We use Aironet 1210, ASC 3.3 Radius Server, LEAP authentication and we trust the Active Directory for the username and password.ACS is installed on the Domain Controller CC. We can authenticate users from the domain CC but we cannot authenticate u...

Aronet 1200 DHCP server is configured on Global Mode. Problem is it gives DHCP clients on Ethernet ( BVI) interface. Is there any way Access Point giving IP only on Dot11redio 0 iterface and not on ethernet side.

Hi,I have configured my AP with the following settings. Some have truncated as the limit to the characters allowed!!aaa session-id commondot11 network-map!bridge irb!!interface Dot11Radio0 no ip address no ip route-cache ! encryption vlan 201 key 1 s...

Hello!I need to test RF environment on two sites. Actually we plan to delpoy outdoor unit with 12 dBi omni antenna. I have such antenna and AP1231G unit. So i want to check if there are available channels and no other interference in the 2.4GHz band....

I have an 1300 Access Point Bridge using 12.3(JA) software. I'd like to use it simply as a repeater (getting signal from an AP1200 to repeat). Under the radio settings, I'm setting it to "Root AP (Fallback to Repeater)". However, when I unhook the eh...

I created a new password in the ap 1200 2 weeks ago, now when ever I want to get into the AP either GUI or console, it would ask for a password. It is not Cisco or cIsCo123. There is a word LEVEL 15 on the left corner of the dialog box. I tried reset...