Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

We attempted to upgrade an AP1220 with a 802.11g upgrade card. The old radio card was replaced with a new card and then we attempted to connect to it with a serial cable to modify the config but could not get logged in. Our login name and password no...

dhardyman by • Community Member
  • 1165 Views
  • 5 replies
  • 0 Helpful votes

Hi,I have a scenario where aircraft service engineers need to have access to a LAN from inside a stationary aircraft (possibly a Boeing 747). The AP 1200 will mostly likely be mounted on a passenger docking bridge either at the cockpit level or the e...

PAUL CHEN by • Level 3
  • 1670 Views
  • 6 replies
  • 0 Helpful votes

Hi,When I issue a show int dot11 command I don't see crc errors and others but using the web based tool I see a lot of crc errors, header crc etc. I would like to know if the web based management tool is a reliable tool? I have already cleaned the lo...

muca by • Level 5
  • 593 Views
  • 2 replies
  • 0 Helpful votes

Hi,I have got two aironet 1100 series access points. They work fine expect I wanted the wireless users to pickup a dhcp address rather than giving them a static address. My DHCP server is on a windows 2003 server and I want the access point to relay ...

yesterdays by • Community Member
  • 738 Views
  • 1 replies
  • 0 Helpful votes

To All: I am looking for any documentation about the 3200 Series Wireless as to what the maximum number of concurrent wireless connections are per interface. I have not been able to find this information anywhere and I have conflicting reports as to ...

gary by • Community Member
  • 387 Views
  • 0 replies
  • 0 Helpful votes

Hi,I have a problem to package the Cisco Wireles Client to a msi file using Admin Studio.Managed to create a msi file, and installed the msi file is OK.But after unistalled the software and rebooted, its crashed the operating system with lsass.exe ap...

eyuwono by • Community Member
  • 760 Views
  • 2 replies
  • 0 Helpful votes

does anyone know why the following happens?i am sitting at my desk with a wireless laptop running a constant ping to the gateway. if i watch the client utility, it will periodically reassociate to a different access point. i am confused in that i am ...

pam by • Community Member
  • 627 Views
  • 0 replies
  • 0 Helpful votes

does anyone know why the following happens?i am sitting at my desk with a wireless laptop running a constant ping to the gateway. if i watch the client utility, it will periodically reassociate to a different access point. i am confused in that i am ...

pam by • Community Member
  • 499 Views
  • 0 replies
  • 0 Helpful votes

hello,I have the same issues on multiple access points (all cisco 1200s - in different sites) in which users cannot authenticate until they walk close to the AP. (a site survey was done before installation) - and I get good link quality from the user...

bwilliams by • Community Member
  • 1586 Views
  • 8 replies
  • 0 Helpful votes

I just read an interesting document about the Cisco WLSE, Air Magnet Enterprise, Air Defense. Since Cisco partnered with Air Defense and Air Magnet stating that they soon too will be able to intergrate with WLSE. Is Cisco leaning towards a new produc...

For hot standby,Should the mac-address of the active AP be the radio interface mac or the ethernet interface mac ?http://www.cisco.com/en/US/products/hw/wireless/ps430/products_installation_and_configuration_guide_chapter09186a0080147d79.html

Can I use the ap 1200 dual band for two diffrent role, 2.4 Ghz for in-building and 5 Ghz for inter-building; if so, the 1200 can be an access point and a bridge in the same time

k64par5001 by • Community Member
  • 779 Views
  • 4 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card