Wireless

I have two fairly close Aironet 350s providing Wi-Fi for users, both connected to entirely different Internet connections, each serving a different segment of users in separate hotel towers. I have a third Aironet 350 in place acting as a repeater, a...

I want to set up a network here in my office using a Cisco Aironet 1231g to test how well the 11b and 11g cards work within a shared 11b/11g environment. Since I've heard some stories of how in mixed environments that b cards will drop all the g user...

Folks, We recently bought WLSE 2.5. I would like to implement WDS for RF scanning (rouge access-point detection). One of the prequists of WDS is LEAP (please correct me if i am wrong). Do we have to BUY a Cisco ACS server. I was under the impression ...

HI,i'm trying to manage a wilan (cisco 1230 Access Point) with snmp, i 'm interestinf about cisco QoS MIB, but there are something that i didn't understand: when i do a 'snmpwalk ' in the Cisc-QoS-MIB, the OID that returns aren't defined in your MIB,...

Is the RF on an AIR-PCM352 derived from a crystal? If so, what is the stability? I assume that it is a PLL/crystal combination, but can find no specific reference in any of the documentation.I need this information for approvals purposes (the client ...

Does anyone know what the maximum number of non-root bridges is in a point-to-multipoint wireless network? I realize the bandwidth is shared, however this not a high throughput issue.

We are experiencing a problem with the latest versions of the client software connecting through the 340 bridges. It seems to work but we are unable to access certain web sites such as yahoo.com or ebay.com. If we go back to the version 5 of the clie...

The Cisco 1220 AP works fine but when I connect to the console port with an emulator, I see the running config, but it does not allow me to input text. It seems the console connection is blocked, but from telnet, i am able to input commands.How can I...

Hello,I just purchased a tc1000 tablet from Compaq and a Cisco Aironet 350 series LMC352 WLAN Adapter. I already have one working with a PCM352 WLAN Adapter, but do not want the 1 inch+ extending past the slot so I went with the LM, which has a small...

Could anyone give me their thoughts on why I would see bursts of Energy Detect Defers occasionally? I will usually have about 20-40 per 5 second interval on my Cisco 1200 with IOS but I will have everyone drop off of the AP for 5-10 min. and during t...

Hi,I am trying to set up MS Peap with the required hardware. I have read through the document ID:43486. In this, the software they use to test for AP1200 was 12.01T. My query is that I am running 12.2(13)JA3 the latest and greatest on Ap1200. Will it...

I have an Aironet 1200 and Cisco A, B, G adapters and they can connect fine the the 1200.When I put any other third party card in such as a Netgear B or a Linksys B adapter, they do not get a signal.I'm very new at this wireless stuff and dont know i...

I looking at the 1200 ap dual radio but with only the g in it. Is it possible or does a dual radio only come with a standard and you can add the other?

Hey GuysI have a problem setting up two ap's. They are 1220B's which have been upgraded to IOS 12.2(13)JA2 they were VXWare before. On the repeater access point I am getting NO AP RESPONEDED and the Radio state is Down. Thanks for any help.Gareth

I have two bridges that were communicating perfectly until the remote bridge's ip address became listed as "unassigned". So, now I cannot communicate with that remote bridge.This looks like a WEP error, but I KNOW the WEP keys are the same.Any ideas?...