Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Can someone tell me if this setup will work and give priority to Voice?Building A350 Bridge 3550 SwitchBuilding B350 Bridge2924 SwitchI will want to prioritize voice over the link between the 2 buildings. The customer will be using an Avaya IP phone ...
Hi,My WGB350 is showing the following message:"0:01:10 S Unable to determine radio type !"It allways happens a few minutes after power on the radio. I updated the firmware to 8.85 but the same problem persists.When it happens, the telnet header shows...
How would I go about configuring an Aironet 1200, that is a stand alone, to be used in a site survey function. I want to push this AP on a cart and leave it in a place that I think is a good location for an AP, and conduct a site survey based on this...
I have a working PEAP (MS-CHAPv2) environment using Win2003 IAS, WinXP sp1 machines, and a Cisco 1200 with 12.2(13)JA1. Here's the problem. I can get any vendors card to work with this except for the Cisco 350 series cards.And the question. Must I in...
Cisco Aironet 350 802.11b card working with 3rd party wireless DSL router (LinkSys, D-link or Netgear) to establish VPN tunnel via Cisco VPN client. VPN session always get drop when using 9600 MHz cordless phone. Is there something between Cisco Airo...
I am seeing a high rate of CRC errors on the recieve end of my root radio for a point to point connection. What could cause the high CRCs the other end has low CRCs.
I am trying to upgrade [AP350, 12.03T] with AP350-Cisco-IOS-Upgrade-Image-v2.img (12.2(13)JA1 )When I try to save the Firmware-Job I get the following messageImageAP350-Cisco-IOS-Upgrade-Image-v2.img (12.2(13)JA1 ) Not recognized And in BOLD REDVxWor...
Can anyone help me in configuring the Cisco Aironet 350 adapter to talk to the Netgear WGT624 wireless router? I've been at it for a couple of hours now and can not nail it down. Thanks Yes, I have the client software installed as this is the same ca...
Folks, I am having some issues with my Cisco aironet 1200 access point, would appreciate if someone could help me out.1) Link shows that i am connected at 11MBs, i have a 802.11G radio in my access point, why not 54MB, i am the only one connected.2) ...
does LEAP limited for only Cisco products (Wireless Cards & Access Points)? what if i have Non-Cisco Card, does LEAP work?
When I use an AP1100 or AP1200 with the 802.11g module and all clients have a 802.11g client adapter I got 54Mbit. Now when I insert in this existing network one 802.11b client (eg. WGB350 or Client Adapter) what about the other 802.11g clients. Does...
Hi all,I have upgraded some of our AP350 to the IOS Image 12.2(13)JA1 with the Cisco Conversion Tool.Now I would like to change the configs via WLSE 2.5, which tells me that it doesn't support this image.Has anybody the same problem or maybe a soluti...
Can I upgrade my Release 1.3 to Release 2.5. If yes.how do I got about it,Tanks
Trying to upgrade IOS on AP1200 from 12.2.11 to 12.2.13JA1 using WLSE. The job just keeps running and you have to ultimately kill the job to stop it. Please help!
I tried to discover 3550-Switche with our Cisco WLSE V2.5. Two 3550 devices working fine (V12.2.(8)EA1)+(V12.2.(9)EA1). Other 3550 devices with V12.2.(13)EA1 didn't respond. I don't know why. (same config) -I checked the SNMP-connection with the WLSE...
