Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi,I recently installed one point-to point link with clear line of sight. I am using 2 bridges aironet 350. The distance between sites is around 15 km.I am using two solid dish 21dbi antennas and 50 ft low-loss cable length each site. I ran the carri...
hello..This is my first time with cisco wlan and i need some pointers.My wlan is up and running on both the 1100+1200. and ive hide the ssid and have implemented wep .What i dont get to work is mac adr locking...i want to manuallly set in the mac adr...
Hi,we are trying to have a PEAP Wireless netwotk with WinXP and 1200 Series.I installed SP1 on WinXP professional machine about 3 months back and still don't see the PEAP option under 802.1x authentication types. The only option availabe is "Smart Ca...
I am currently designing a Wireless solution for a customer in a fairly large network. It is not reasonable to plug all access points into one physical switch in their network. Are there any guidelines for configuring switches to allow roaming for wi...
I get the following message, and all of my clients get kicked off. They then re-associate. What is this?!?!Disassociating [10.0.1.15]00072570a26e, reason "Sender is Leaving (has left) BSS"
Hi All, Please what is my problem? I use Cisco Secure Access Server Version 3.0 for Windows 2000/NT Servers to authenticate users on our wireless network. I however wish to assign monthly time limits to each user after which he/she will no longer hav...
In mapping out an 802.11a WLAN with many APs, What is the best Channel Assignment Scheme to use? What must the separation be between channels in adjacent cells? 802.11b is a 5 channel separation, What about 802.11a?thanks,Frank
My problem is that sometimes the assocation table does not fill in all information about other access points on the network. All the access points are on the same vlan. Most of the time it is the IP address of another access point that is missing. I ...
We are currently running Aironet350 LMC352 cards in our wireless workstations. and have set the Power saving settings to MAX PSP.When ping the workstations, the response time is > 100 ms (but we do not lose any packets).When we switch the Aironet car...
Repeater limit: hops or leafs?Starting with the following configuration..AP Root ---- Rpt 1 ---- Rpt 2..I know that available throughput will be divided by two if we add one more repeater to Rpt 2Question: Is the effect the same when you add several ...
Does anyone know of the maximum number of clients that can be supported an a 350 bridge running in AP mode. I need to provide network connectivity to a housing estate (1.5-2mile radius) at a minimum of 1 Mbs. I was thinking of using the 350 since it ...
We have an Aironet 1200 Series Access Point that I am trying to set up for our shop employees. When I go into IPSU and enter the MAC address that is listed below the unit and click on get IP Address, it says device does not answer. Then, when I click...
I have one Access Point 340 connected to my Cisco 3550 Switchand I have another Cisco Work Group bridge connected to another switchwith 4 clients on it.I can communicate with access point from the hosts via workgroup bridgeonly if I have static IPs b...
We are using aironet 350's and want to know why different speeds are quoted as different distances, is it to do with quality or something? Thanks
I am trying to connect a BR352 multifunction bridge set up as a root bridge to computers with aironet 350 client adaptors over water at distances up to 9 miles.I have line of site and am using high gain antennas and amplifiers to RF attenuation shoul...
