Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
We are getting the following error on non-root bridge. The bridges are setup to communicate with MIC, TPIK, and Leap. We are not able to setup WEP on the non-root once leap is enable. Is this message something I should be concerned of? I am able to c...
Hi, I am trying to set up 802.1x on a Catalyst 4006 with a Supervisor III module with IOS 12.1(12c)EW1. I am using Cisco Secure ACS 3.0(2) Build 5 for my Radius server. I'm using the Windows 2000 802.1x hotfix for my 802.1x client software. My goal i...
I am trying to find documentation on the features of wlse software 1.3. I am currently running 1.0. Does anyone know the whereabouts of the release notes and steps involved for the upgrade. Any help will be greatly appreciated
I've a WGB350 associated (no encryption at the moment) to an AP350 :host ------ WGB350 - - - - - AP350 ------ routerx.x.x.99 x.x.x.250 x.x.x.217 x.x.x.1The role of the AP is "root", and the WGB it's seen as a "repeater".I didn't configure any route n...
I have a 350 AP (v12.00T) setup for Network-EAP. When I try to associate with it I keep getting "EAP retry limit reached for Station". I've sniiffed the ethernet port and the AP is not even trying to contact the Radius Server. Anybody have any ideas ...
I would like to develop a report package for Cisco Wireless device using the SNMP (MIB Objects) access. Can anyone suggest me what are all kind of report i can produce ..?Like, CPU Usage, Memory and Buffer Usage, Process utilization and Conne cted No...
hi engineers ,i want to use 1200 access points in my local lan and 802.11a 5ghz standards so i had search over cisco equipments .my problem is that i have found access point and client adapter but i still looking for pci card for pcs not notebooks.pl...
Hi,How to monitoring latency between two wireless points (WWAN)?I would be grateful if you advice me.Best Regards,Mehrdad
My company where i work for, we have licence for broadband fixed wireless access for Indonesia at 28 Ghz and 58 Ghz. Can anyone help me for solution: include instalation, hardware, software. Because we don't have any idea for that, we only have the l...
We have about 6 aps in a baggae sortation room where 2 ap are on different switch, the clients use scanner that just talk to a web page, they complain about the internet explorer e just spinning, what I found out was that I had to adjust the cell siz...
I have a 350 to 350 bridge W/ a 2 mile run and they work well <10ms Response.when a good bit of data is passing it does the de-Authentication and then a couple of minutes later it re-authenticates and re-associates and it will be fine both bridges ca...
Hi All,recently installed the AP 350, and can work properly. But today, I cannot see the status of the radio, only ethernet port is UP.Therefore I can't use the wireless client card at all. No signal at all.How to solve the problem?TIA,Andi
I have a demo WLSE that I upgraded from 1.1 to 1.3. For the many switches it discovered along with APs, it is declaring for each of them : "Switch memory utilization is Degraded (66%)" -or some other percent. Is this a glitch? Anyone else seeing this...
Can the Cisco Aironet 350 run NAT?
Is there a way to change the 350 MiniPCI client MAC address in XP or with the Aironet utilities ?
