Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
We have a wireless connection constantly disconnecting. Air Marshal "AP spoof" has many listings. could this have something to do with it??
I've searched online and struggling to find a yes or no answer to keep it simple.Has anyone ever sucessfully been able to configure a MX device (broadcasting the same SSID's) to a MR33/MR44 in a mesh using repeater mode to seemlessly keep signal (no ...
Resolved! SNMP OID for AP Radio Throughput
What is the WLC OID to collect the throughput per AP radio? I have been digging through the MIB tree for my WLC AIR-CT2504-5-K9 but haven't found it. The WLC Monitoring Dashboard shows this, but I need to collect it over SNMP.
Hi - While reviewing the logs for Network-wide>Clients>Usage> Details (pie chart), I see 'Unknown' listed under Destination with a significant amount of Active Time under it. Could you please let me know what kind of website/URL could this be? Also, ...
Hi, i wanna ask before i will buy MR76 outdoor, if we buy MR76 is it incluse 2 set antenna ( i mean 2 anttenna 2,4 Ghz and 2 anttena 5Ghz) or i will buy separate.Thank you
Hi c9800 wlc has guest ssid. Under the same WLC, we can see two guest State(Monitor---->Client) when user access the guest ssid. One is "Run" and second is "Web Auth Pending". What reason cause the second state? Thank you
Has anyone been able to configure WPA3 & 802.11r on the new MR 30.1 beta firmware?I have an MR46 & MR36H in a network running MR 30.1.Dashboard continuously rejects the config, saying "The current WPA encryption mode does not support dot11r."I've tri...
I have been receiving these error messages while I'm trying to join a LWAP to the WLC. I tried running the command config ap cert-expiry-ignore mic enable on the WLC, but it won't work.WLC software version is 7.6.100.0.AP model AIR-CAP3502I-E-K9AP im...
Hi, We are currently using WLC AIR-CT2504-5-K9. It has reached end of support in April 2023. Therefore, we hope to replace model C9800-L-C-K9 instead of AIR-CT2504-5-K9. Now we have connected the AP models AIR-AP1832I-E-K9C and AIR-CAP1702I-E-K9. do ...
Hi All, Running fabric in a box on with wireless enabled, on a stack of Cisco Catalyst 9300 Series Switches (C9300L-48UXG-4X / C9300L-24P-4X). Need to upgrade the WLC version from 17.3.4 to 17.6.4 - Can this be done on the WLC only or does the stack ...
Hi all,I'm trying to connect new APs to WLC at a new location and the APs are joining and seconds later they are disconnecting from the WLC. When I consoled into one of the APs it's showing the output I have attached, below is part of what I'm seeing...
Hello,I recently raised a ticket with meraki because I have a MR74 that seemed to be stuck on a low TX power (well below 20).They explained that its because the regulatory rules say the max power is 20 (or 23, somewhere around there) - and with the a...
Hi All, Running 9800-40 WLC's Version 17.6.4 and DNAC Version 2.3.3.6-70045, would like to utilise the new AP "ZONES" feature via DNAC. What version of WLC code is supported? Any docs/advise would be helpful. Cheers,
Dears,I have a cisco 1852i as master mobility express and i have bought cisco 2802i.can cisco 2802i join as subordinate AP under 1852i ??????
We are currently using the AIR-CT2504-5-K9 wireless LAN controller (WLC), which reached its end of support in April 2023. Consequently, we are looking to replace it with the C9800-L-C-K9 model instead of the AIR-CT2504-5-K9. Currently, we have deploy...
