We have a wireless connection constantly disconnecting. Air Marshal "AP spoof" has many listings. could this have something to do with it??
Forum Posts
I've searched online and struggling to find a yes or no answer to keep it simple.Has anyone ever sucessfully been able to configure a MX device (broadcasting the same SSID's) to a MR33/MR44 in a mesh using repeater mode to seemlessly keep signal (no ...
Resolved! SNMP OID for AP Radio Throughput
What is the WLC OID to collect the throughput per AP radio? I have been digging through the MIB tree for my WLC AIR-CT2504-5-K9 but haven't found it. The WLC Monitoring Dashboard shows this, but I need to collect it over SNMP.
Hi - While reviewing the logs for Network-wide>Clients>Usage> Details (pie chart), I see 'Unknown' listed under Destination with a significant amount of Active Time under it. Could you please let me know what kind of website/URL could this be? Also, ...
Hi, i wanna ask before i will buy MR76 outdoor, if we buy MR76 is it incluse 2 set antenna ( i mean 2 anttenna 2,4 Ghz and 2 anttena 5Ghz) or i will buy separate.Thank you
Hi c9800 wlc has guest ssid. Under the same WLC, we can see two guest State(Monitor---->Client) when user access the guest ssid. One is "Run" and second is "Web Auth Pending". What reason cause the second state? Thank you
Has anyone been able to configure WPA3 & 802.11r on the new MR 30.1 beta firmware?I have an MR46 & MR36H in a network running MR 30.1.Dashboard continuously rejects the config, saying "The current WPA encryption mode does not support dot11r."I've tri...
I have been receiving these error messages while I'm trying to join a LWAP to the WLC. I tried running the command config ap cert-expiry-ignore mic enable on the WLC, but it won't work.WLC software version is 7.6.100.0.AP model AIR-CAP3502I-E-K9AP im...
Hi, We are currently using WLC AIR-CT2504-5-K9. It has reached end of support in April 2023. Therefore, we hope to replace model C9800-L-C-K9 instead of AIR-CT2504-5-K9. Now we have connected the AP models AIR-AP1832I-E-K9C and AIR-CAP1702I-E-K9. do ...
Hi All, Running fabric in a box on with wireless enabled, on a stack of Cisco Catalyst 9300 Series Switches (C9300L-48UXG-4X / C9300L-24P-4X). Need to upgrade the WLC version from 17.3.4 to 17.6.4 - Can this be done on the WLC only or does the stack ...
Hi all,I'm trying to connect new APs to WLC at a new location and the APs are joining and seconds later they are disconnecting from the WLC. When I consoled into one of the APs it's showing the output I have attached, below is part of what I'm seeing...
Hello,I recently raised a ticket with meraki because I have a MR74 that seemed to be stuck on a low TX power (well below 20).They explained that its because the regulatory rules say the max power is 20 (or 23, somewhere around there) - and with the a...
Hi All, Running 9800-40 WLC's Version 17.6.4 and DNAC Version 2.3.3.6-70045, would like to utilise the new AP "ZONES" feature via DNAC. What version of WLC code is supported? Any docs/advise would be helpful. Cheers,
Dears,I have a cisco 1852i as master mobility express and i have bought cisco 2802i.can cisco 2802i join as subordinate AP under 1852i ??????
We are currently using the AIR-CT2504-5-K9 wireless LAN controller (WLC), which reached its end of support in April 2023. Consequently, we are looking to replace it with the C9800-L-C-K9 model instead of the AIR-CT2504-5-K9. Currently, we have deploy...
