Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Hi all,I'm pretty new to networking and we have an office move where the networking person just left the company. I need to help move 1 Meraki MS120-8LP 3x Meraki MS120-48LP switches . Is it just as easy as assining the new IP addresses to the Meraki...

py2o3434 by Community Member
  • 2526 Views
  • 4 replies
  • 0 Helpful votes

Hi, I had one problem which I found bypass solution, but I would like to share with someone, as I don't want that someone is wasting time as I did troubleshooting the issue.My case was that I have 15 APs AP1832i set to Cisco ME, so 1 acts as a call i...

dovla091 by Level 1
  • 103015 Views
  • 64 replies
  • 16 Helpful votes

I'm hoping for some help here, I'm trying to fire up a new Cisco 9800 WLC for first use, and for some reason I cant get the DHCP discovery from the client to be forwarded to and external DHCP Server.  I enabled the DHCP Service from the CLI, also ena...

donniebman by Community Member
  • 22902 Views
  • 6 replies
  • 0 Helpful votes

Helllo everyone, I have an issue, our AP is VID 07, as check from Cisco Wireless Solutions Software Compatibility Matrix - Cisco it seem that it is not able to join the WLC 5520 version 8.10.130.0, unless we upgrade the WLC to 8.10.181.0 or later.May...

Sunly by Community Member
  • 2451 Views
  • 3 replies
  • 0 Helpful votes

Resolved! IPSK VLAN Tagging?

Hello,I'm a little confused about the VLAN tagging on IPSK and couldn't find an answer in a guide anywhere.We are not using radius and have several different identities defines in group policy. Each identity has a different VLAN assigned in the Group...

Adrian41 by Level 6
  • 7086 Views
  • 10 replies
  • 0 Helpful votes

Hi!Trying to do some external logging of mesh SNR/dB numbers for AP:s that move around on our site in a mesh-network. I can fetch a lot of stats via SNMP but for example this clMeshNeighborLinkSnr .1.3.6.1.4.1.9.9.616.1.3.1.1.3 in CISCO-LWAPP-MESH-MI...

tjswenet by Community Member
  • 760 Views
  • 1 replies
  • 0 Helpful votes

How flex connect in wlc works? Does it form any VPN tunnel from remote site AP to centralized WLC over WAN? I am bit confused over it's WAN operation. Really appreciate if anyone can help on this.

In a CW9164 Proof of concept the 9164 APs are reserving 47.2 Watts of POE from the 9300L MGIG Switch that they are connected to. As per the data sheet with the USB turned off they should only be reserving 25 Watts. Is there an explanation for the lar...

Can anyone please tell me what does this output from debug client means ?IPv6_Msg_Task: Apr 17 13:21:53.884: [PA] 80:b6:55:d9:5d:c8 Link Local address fe80::82b6:55ff:fed9:5dc8 updated to mscb. Not Advancing pem state.Current state: mscb in apfMsMmIn...

rhallan by Level 2
  • 2102 Views
  • 5 replies
  • 0 Helpful votes

Hi guys,I use CWB 150AX AP + WPA2 Enterprise (certificates) based on Windows NPS.There are a few clients that sometimes disconnect for no reason, and some can't connect at all.No error on NPS log or on the client side.found this in the AP log, can't ...

vadimsh207 by Community Member
  • 1985 Views
  • 4 replies
  • 0 Helpful votes
Top Solution Authors
Review Cisco Networking for a $25 gift card