Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! 2802i AP blank NAND, how to recover?
I recently acquired a lot of second hand 2802i access points. It appears that one of these APs has a blank NAND flash chip. AP boot loops at U-Boot until I break into U-Boot with escape key. Upon checking "nand info" nand 0 is seen, and checking "ubi...
Has this bug been resolved in FW release 17.9.6?
Hi everyone. When implementing Wi-Fi 7 APs, are there any recommendations on which WLC deployment mode to choose (e.g., Centralized Design (Local Mode) or Distributed Design (FlexConnect))?Considering the increase in bandwidth, I feel that a Centra...
Resolved! Wireless Clients Unable to Ping C3850
Hello all,I have a C3850 setup with the attached config, 3850 is the WLC with an attached 3802 AP. This is a test setup I am working on and I am having an issue with the wireless clients. They are able to connect to the WLAN (vlan30) and successfully...
Hello Team,2 different client devices are using same IPV6 address due to which, WLC is deleting those clients due to IPTheft feature.Two different clients (286b.35a9.477d and 5c3a.453a.a41b) are using the same IPv6 address, which is not allowed for t...
Hi,We have a batch of 9130AX's that will not save the pre stage configuration, no invalids are seen on the CLI.Adding hostname does not change the device from MAC to given hostname and when sh cap cli conf is applied control names and IP's are missin...
Hi team, May I Ask what it means when C9130AXI-A have solid white on LED indicator. however, the AP is not up on wlc just solid white this issue been encounter during the implementation. help me on this please.
Hello Experts, Can we use the same WLAN for 802.11r capable and non 802.11r capable clients? Are all CCX v4 client capable of supporting 802.11r? https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/80211r-ft/b-80211r-dg.html Below is...
Resolved! WLC 9800 MAC filter multiple wlan
Hi friends, I'm configuring a WLC 9800 17.9.4.a. MAC address filtering works, but it doesn't respect the WLAN space.For example, I want MAC01 to connect to WLAN profile Test02 but not to WLAN profile Test3, and I want MAC02 to connect to WLAN profile...
Hi All,We're about to upgrade our WiFi network architecture. Currently we have a Foreign/Anchor setup for direct internet access. Is this the current Cisco recommended architecture? A colleague has suggest a new architecture removing the Anchor an...
What is the criteria to create SVI and VLANs in the 9800. If you take multiple AP management bands (vlan) to the same network Do I have to need several SVI and/or Vlans?
Is it possible to connect Aironet AP 1560 series to C9800 WLAN controller for centralized management.
Dear Alli have cisco 3504 controller running 8.5.182.108 at small site i want to upgrade it to Release 8.10.196.0we have existing mobility tunnel between 3504 and 9800 controller for guest WLANi have question that 8.10.196.0 is compatible with 9800...
Resolved! 9800 disable a client
Hi All-How do I disable a client by mac address? I have not had to do this since the 5500 days where I entered the mac under Security -> Disabled Clients -> Manually Disable. What is the similar option on the 9800?Thanks!
Well I've got the new WLAN access point, also got the paper with instructions for RMA (sending back the faulty part).I already did this a few times before.But the last 2 times it did not accept the RMA number, so I could not create return form for ar...
