Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
The local supplier installed some MR 76 APs for us, but they seem to have installed it wrong with the MR74, the antenna wire they installed is as shown in the attached picture, I know they installed it wrong. But the number of APs is quite large and ...
i have cw9166I-ROW and in this have cisoc capwap images and this model support C9800 WLC and meraki and i want to use in meraki dashboardso now i think have only capwap images i dont have any wlc so how to convert image for meraki supprt so automati...
How many of these do you have in your environment? And those that do have, will you still have them past the July 31, 2026 cutoff for EOL/EOS?We have a large number and will be carrying some past the cutoff. People are debating shutting them down ful...
I've a typical customer scenario where they recently upgraded to wifi7 (9176I) APs from older (1700/1800) series of APs. WLC 9800 is running code 17.18.3now the issue is, since the installation of these new APs is done, the client laptops (though sta...
Dear all, I have an AP AIR-AP1572EAC and wanted to reset to default but all times I try to reset it, it competely does not get to the default. I unplug the power cable and press the reset buton and connect the Power cable back, and the LEDs would tur...
Hello,I would like to get a list of the associated APs on my controller. I would like the list to show the name of the AP, the Ethernet MAC, and the Base Radio MAC address. I planned to do a show run-config, save that information to a file and then...
1.AIR-CAP3602i-A-K92.useraname and password
I have a working CBW 150AX mesh network with six devices. I need to setup another mesh network on another vlan. The first device is stuck at the led green-red-off sequence. I've used chatgpt to find solutions but so far nothing has worked. Thank ...
Mediatek MT7925 WiFi7 NIC - MR56 sends "Status code: Association denied due to requesting STA......"
Im currently troubleshooting a new laptop that cannot connect to MR56 AP.Its clear that it fails association from packet captures, the AP responds with:"Status code […]: Association denied due to requesting STA not supporting all of the data rates in...
Resolved! CW9174I in Meraki Dashboard
Hi,I've a question, is the CW9174I officially supported by Meraki (Dashboard) ?I don't find any document.Same for CW9171I.
I'm having a similar problem. When I restart the AP 1572 and the LED turns red, it restarts, but I need the AP MODE to stay just as 'flex'. However, when the AP restarts, it goes to 'Flex+Bridge', and besides only erasing the hostname, the TAG config...
I have thousands of APs in Catalyst Center, when we originally placed the APs on maps, we made mistakes with providing correct height/tilt angle etc. If we can download this info from catalyst center as an excel file and later can edit it and upload ...
Hello everyone,I am currently expanding my home lab environment for further testing and professionaldevelopment, and I recently acquired a Cisco Aironet AIR-AP2802I-E-K9.My goal is to flash the AP and run it in a standalone/controller-less deployment...
Resolved! WLC 9800 , UNII-1 & UNII-3
Hello Cisco Wireless Community,I am currently investigating a DFS-related issue on a Cisco Catalyst 9800 deployment with CW9176I access points in France (EMEA regulatory domain).I would like to clarify whether there are any Cisco, regulatory, or plat...
Hello,We have a couple C9105AX installed running EWC 17.15.3 good coverage currently set at 80mhz for 5ghz seeing 1200mbps link on wifi settings on my Mac.But in reality on iPerf or speedtest only getting 250-320mbps.PC via ethernet getting 1GB.IPerf...
