Hi folks, I noticed some of wireless client faced DHCP renew issue when I using C9500-48Y-4C as DHCP server, and C9800-40 as wireless controller (Access point is using local mode).During DHCP renew, the wireless client will send the DHCP request pack...
Forum Posts
Hi Guysi have subject (SW 17.3.3) continuously landing me to configuration wizard https://X.Y.Z.N/webui/#/dayzeroPnpOrCli.i just need to go to expected C9800 GUI for further WLC configuration. How can i bypass this page (it starts asking basic settin...
Hello everybody, we have a Cisco Aironet 1562 that we are trying to connect to an existing SSID (provided by an AP managed by a WLC).The access point need to bridge the SSID to his ethernet interface, where a PC is connected, using WorkGroupBridge mo...
Resolved! Switch for fabric enabled APs
I need to buy a new switch to support APs in a new area. This particular switch will just support APs. Initially, they will be local mode CAPWAP APs, but in the future they will be part of an SDA fabric. Any limitations if I use a Cat9200 vs Cat9...
Does anyone know where to find the definition as stated in Ethernet Connectivity Fault Management (CFM) extensionfor microwave devices as defined by Cisco ? See Cisco document attachment, G.8032 and CFM Support for Microwave Adaptive Bandwidth, for...
Resolved! Traffic Shaping Advice
Hi there,Here's a little background for context: I work in K-12 where I have a high school with around 3000 students and about 175 staff. We are a 1 to 1 district where students get Macbook Airs and staff gets Pros (and several shared laptops, deskto...
Hi Please see the below diagram with central dhcp server. Not sure how to define the "central". When we create dynamic interface at wlc, we need to enter dhcp server ip address. Can we say this dhcp server is central dhcp server? otherwise is local d...
Hello Experts , for one of my sites, i had to de-commission the local and had the ap's flexconnected to a regional wlc which is a 9800.the ap's are 2800I and using flexconnect local switching now once the change was done, user started complaining low...
Hello, i changed my wifi setup from Unifi to Cisco and make my first steps.In syslog i cab see many entries like the following messages%RRM-3-RRM_LOGMSG: rrmLrad.c:5634 RRM LOG: Failed to lookup data rate for encoding 35389926, with channel width 20 ...
Hello there, I added an AP Group on a WLC Cisco 5508 but this AP Group does not appear in Prime 3.9.0.In Prime there is an issue "Wrong CLI Credentials" does this correspond to the missing synchronization mentioned above?Also the associated APs which...
I have AIR-CAP2802I-E-K9 AP and it was working fine, suddenly it was disassociated with WLC, I found its static IP configuration was washed out, I tried to prime it through console and on that time it was associated with controller, as i powered off ...
Dear all, anyone has any recommendation what are the requirements from Catalyst 9800 (IOS-XE 17.3.3) configuration point of view (Flex Profile, Policy profile,...) in case you have an AP which suppose to broadcast locally switched WLAN, however on lo...
WLC Cisco IOS XE Software, Version 17.06.01C9800 Software (C9800_IOSXE-K9), Version 17.6.1, RELEASE SOFTWARE (fc6)AP ver 17.6.1.13 My 1+5T phone (Snapdragon 835, Android 10, Security patch 2020.09) won't connect to SSID.I've tried configurations like...
Trying to convert 1572E from lightweight to autonomous but not working. Configured and IP in ethernet port and bvi interface. APac3a.6744.a720#ping 10.1.1.1Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds...
Greetings, The 9120 AP needs to have the CA certificate as trusted certificate so that it can connect to the RADIUS server and authenticate as Dot1x supplicant. Could you advise how to upload the CA certificate to the AP ?. The WLC is a 9800. Regard...
