Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Planning to upgrade WLC from 8.0.121.0 to 8.5.161.0When checked sysinfo, I am seeing the Bootloader version as 1.0.20.Kindly let me know whether the bootloader version will create any issue.Also let me know how to upgrade the Bootloader version.
Hi I have a single Cisco 3800 running Mobility Express. Unfortunately, I have been trying to set it up with 160 or 80+80 but it gives an error "unable to assign IPAddress" and then all radios shut off and then I have to turn them back on manually. I ...
[*02/02/2020 16:27:41.4927] CAPWAP State: Discovery[*02/02/2020 16:27:41.4927] IP DNS query for CISCO-CAPWAP-CONTROLLER.FarmFritesEgypt.com[*02/02/2020 16:27:41.4927] DNS resolved CISCO-CAPWAP-CONTROLLER.FarmFritesEgypt.com[*02/02/2020 16:27:41.4927]...
I am not be able to enable the TKIP for WPA2 with Wave 2 access points and controller firmware above 8.5.xx Please find waring message seen. Warning! WPA2 TKIP cipher is not supported on Wave2 APs for WLAN 2 Please share the all possibility to enable...
how to configure AIR-AP2802I-K-K9C and its mount on ceiling and its connected to switch?
Hello Everyone,I'm wondering if you experience the same behavior I am getting from my outdoor AIR-LAP1522A. The access point is powered normal and the switch can detect it from the sh CDP neighbor.in addition, AP is able to reply on ping. but it does...
Resolved! AP firmware version stuck at MR 26.8.1 even after firmware MR 27.5.1 was updated successfully
Hello Community,We have a wireless network of MR32, MR33, and MR18 APs.Their current firmware states they are on version MR 26.8.1, so we updated the AP firmware to MR 27.5.1.The dashboard states the AP firmware version to MR 27.5.1 was updated succe...
Hi everyone i have AIR-CAP3502I-E-K9 as stand alone connected to my cisco isr and the maximum speed I can achieve is about 47mbps on 802.11n . I tried setting different modulation and channel width, inreasing antenna power etc. and nothing! below is ...
For secuirty purposes I have created ACL for new SSIDs and looks like it does not work correctly. 10.2.25.0 is the interface of new SSID trying to get access to 10.2.115.0 which are APPLE TVs basically when I take off the ACL all is working, when I...
This summer the IT department at my location rolled out a little more than 100 AIR-CAP3502I-A-K9's to much success. We have had an issue with only one AP. This paticular AP must have gotten unplugged during the updating process after the initial conn...
Hi Friends,looking to setup a meraki PTP link for a golf course.i was curious as to if meraki might have anything in it's antenna ranges that could allow me to beam point to point from 1400 ft apart.i was looking at the AIR-ANT2513P4M-N as it looked ...
Hi all- I am looking for a wireless bridge - to plug in a wired device and access the wireless network. I would prefer a device that does EAP-TLS. We have been using APs in workgroup-bridge mode, but I am hoping to reduce the complexity and price a...
Resolved! Users cannot access Internet from Wi-Fi
Hello,We have a Wireless network that consists of 24 MR84 and 44 MR42 APs. I've configured all of the APs to received their IP from one VLAN, while the users receive their IP from the specific VLAN for their facility. At this point, users some buildi...
delete
I have open the cleanair and 802.11b can see some date. but i can't see 802.11a date, i don't belive no interference,beacuse i can see some interference in dashboard.
