Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
So i tried installing a embedded controller on my 9120 accesspoint. Following each step from the guides... After reboot i got:APF4BD.9EBC.F140#capwap ap EWC-AP in Recovery Mode......Please use 'archive download-sw' to upgrade AP and Controller image...
Resolved! need help
I want report about uptime and downtime of all APs .where to find ?
Here is a photo gallery and unboxing of a Cisco WiF-7 CW9176I-RTG Access point.I needed some visibility and access to the 6Ghz frequencies so I upgraded some older MR42 APsto the new CW9176I APs. The single PID made ordering easy and the include brac...
How AP - C9120-AXI-B is adapted with WLC 5520 where the AP version is 17.12.3.31, as per ap compatibility matrix the AP version should be - 15.3(3)JK9, not 17.12.3.31.
Hi, we have a Cisco Catalyst 9800-L WLC that we would like to configure WPA2+WPA3 transition mode on for the WLANs. We have some WLANs that are meant for both APs that support WPA2 and WPA3 (For example AIR-AP2802E-K-K9), as well as APs that only sup...
Resolved! Control Path Down
Hi,The control path between our Guest Anchor WLC4402 and one of our foreign controllers is down all other control paths are up as are all of the data paths. The Anchor is behind a firewall the configuration of which must be ok due to the other WLCs d...
Hello Meraki Community,We’re planning to scale our wireless network to handle increased device density and higher bandwidth demands. I’m exploring expansion modules (like the MA-ANT-20 or MA-IN-6-20-XW) to enhance our MR access points but would appre...
show versionProcessor board ID FCW2248NR7JAP Running Image : 17.17.0.87Primary Boot Image : 17.17.0.87Backup Boot Image : 0.0.0.0Primary Boot Image Hash:Backup Boot Image Hash:1 Multigigabit Ethernet interfaces1 Gigabit Ethernet interfaces3 802.11 Ra...
Hello,We've been experiencing issues with the MR70 model (although this could apply to any MR device that doesn't support the designated firmware version—you'll see what I mean).A customer reported roaming issues between indoor and outdoor APs. Their...
I have several sites with flex-AP associated to 5508 Cisco Flex WLC (software version 8.5.161.11). A couple days ago CPI alarmed IDS 'EAPOL flood' and IDS 'Auth flood' signature attacks are being reported by all of my APs across the sites. What might...
Please ignore
I have a 3802i-z access point that is stuck in the u-boot>> environment. I wanted to ask how I can install the IOS on it so that it boots up properly.Below, I am also including the messages that it shows.BootROM - 1.78 Booting from SPI flash, Secure ...
Hello,I'm having an issue with another 9120AXI-B access point.What's Happening:Bought AP from eBayThe AP is stuck in the u-bootI cannot get to the AP loginI'm stuck at the ">u-boot" promptI found these two documents explaining how the AP can get caug...
Hi,My AP 3802I is discover on WLC 9800L install on VM but SSID is not broadcast. we remain the setting as default on wlc9800L
Hi Team, We have deployed 9800-40 WLC's which are in HA SSO and for RP port connectivity we have used fiber RP port direct connection now we want to connect secondary RP port which is RJ-45 which will be through L2 swithh. Please confirm whether it i...
