Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
How to check POE power requirement of AP i.e. 1852I,1852e,2802e
Hi all,I bought AP 3800 -S and I am in Viet Nam, so as I know, I bought the correct model for reg domain. But 802.11ac : not supported. Please advise.Using controller AIR-CT2504-K9
Hi,I have Meraki configured to use WP2-Enterprise using Windows as NPS server. There are multiple polices configured e.g. policy 2 is to check if user is part of certain windows group and it works perfect, here is that policyI have created another po...
Thanks for your help!I'd like to know if I can clear all DHCP leases in just one WLAN through the Wireless LAN Controller. Regards.
Hello to all,I have a WLC Cisco 25series an many access points. Suddenly we face an issue with airprint wirh a Xerox Device, probably bacause of of Mdns configuration. Can you help me to find the reason i 'am not able to print even if the print is sh...
As we have 9200L-24P-L which have 600w power supply and as per update we should not exceed 80% of that while connecting Ap.So if I have 30 watt power required AP then I can connect only max 16 AP to this switch as I can use 480 watt onlyPlease let me...
I'm trying to configure an autonomous 1142 as a work group bridge, to hook up to a printer that doesn't have a wireless card. The SSID I'm trying to connect to, uses WPA2 Enterprise, 802.1x+CCKM, PEAP username and password authentication. How do I co...
I'm working on setting up the Cisco vWLC controller as Hyper-V VM. I've downloaded the ISO, MFG_CTVM_LARGE_8.5.161.0.iso, and believe that I've followed the Hyper-V setup guide correctly but the controller doesn't boot up - it shows an error"Starting...
Hello! Having an issue since we upgraded our wireless controller to 8.10.121.0 where any laptops with the Intel 8265 or 7265 cards intermittently disconnect and reconnect. Very poor performance and cannot keep a consistent connection. I know on a pr...
We've one instalation with a Mobility Express (AIR-AP1852I-E-K9C) working with two AIR-AP1852I-E-K9 (Software 8-3-133-0 in the three cases). Recently we bought a new CAPWAP (AIR-AP1852I-E-K9) and we put the software 8-3-133-0 but can't connect with ...
Hi, I'm trying to joing a AIR-CAP2602I-E-K9 to my 1852i with mobility express. Regarding to https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/8_4/b_cisco_mobility_express_8_4/b_Mobility_Express_Deployment_guide_chapter_0100.html th...
Resolved! 9130AXI-EWC Only connecting at N speeds
Hi team, What is the trick to enable AC and AX speeds on the 9130AXI-EWC? The CLI for 'ap dot11 5 dot11ac' indicates that A needs to be disabled first. Help says 'ap dot11 5 shutdown' will disable A, but as expected, shuts the whole radio off. Thank...
hi GuysI have a problem.I got a new MR33 and 4 new MR42e APs and should set them up.The APs are connected to a Cisco 2960 switch, switch port is configured as a trunk with Native VLAN 555.VLAN555 also assigns the IP address and comes on the Internet....
I have one of these and a couple of 1142 AP's that I would like to learn with.I've had this on a shelf for a long time now, and I pulled it off over the weekend and started taking a look at it again.I found that it is EOL and I cannot find anything o...
