Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! Global Configuration - Login Credentials
Hello Community,I am required to log into a number of FlexConnect Access Points (APs) to troubleshoot some DHCP issues that are occurring on a number of end user clients and unable to enable SSH and Telnet due to the following error:"Failed! AP has d...
Hi, My Wireless device connected to the WAP is having issues regarding connectivity to the network.This is what happens. 1.) When using an internal DHCP scope (with DHCP proxy enabled -> cant be disabled), the Wireless Device gets the correct DHCP in...
Resolved! AP2602 - Speed 50mbps and 100mbps
HelloI have installed per now me AP2606 Autonomous this are connetect on LAN side with 1Gb TP-Cable.i think that i have configured good. but one question about the Speed? i read also on Cisco Paper that this AP can be transfer Speed up to 400mbps i c...
Hi allPrime 3.5 does not show APs and Clients of WLC9800. Inventory Status shows "Partial Collection Failure".On the WLC I noticed that Telemetry connection is stuck in "Connecting".Does someone know how to fix this?Regards,Urs
I have installed a fresh Cisco Prime Infrastrucutre (PI) 3.6 appliance under vmware and we dont see (Inventory / Device Management / Network Devices) the unfield access points in PI from the cisco 9800-cl wlan controller. The only thing what we see i...
Hello,I am going to deploy WLC 9800-40 and WLC 9800-L-F in our network. Both will be running latest 17.2.x WLC version. We have ISE 2.1 patch 14 running currently in the network.We have CWA configured for wireless clients in the network and all is wo...
TestTestTest
Resolved! Stops communication from one AP
Hi All,Need one design help. We have two lightweight APs configured in different AP group and flexconnect group. Both AP are on same floor. We want request of some user go through one AP and other user group should go to other AP .But its not happen...
Resolved! AP throughput
If there are four SSIDs in an AP, would it be 100/4 if the AP had a throughput of 100?and share bandwidth?
Hello I am very new to Mobility Express. I got quite far in setting it up, but I think I missed an important step ... I have two 4800's running AIR-AP4800-K9-ME-8-8-130-0.tar and they were working perfectly when they were connected to the same sw...
Hi, I am currently receive some of the IW3702 and looking on the documentation it has PoE-Out Port. I know to enable it we should apply power from PWR Port. I currently try to implement the IW3702 as Mesh AP connecting to a RAP AP1572EAC. The Mesh li...
Resolved! Power level of Access point
I am currently running WCS 7.0.164 and 1130 series access point firmware 7.0.98.0.I am getting lot of complains from students that their laptops are not getting 5 bars signals. They are getting at least 1 or 2 bars with being disconnect frequency. ...
Hi, I've just updated my C9800-L to IOS-XE 17.2.1. I'd like to test the zero day configuration via website but the standard credentials (webui / <serial number>) does not work. Do you know if it was changed in the new release?
Hi,I am trying to run the WLAN poller tool against WLC 5520. User authentication is via ACS. I am using AAA credentials for the poller tool to authenticate for WLC and AP. But when I run the tool, i see error message that the WLC failed to respond.Is...
Hello, i have a problem with provisioning the AP2700. After the prime procedure was configured, the AP restarted. but now he gives me the following error: *Aug 13 13:56:07.395: %CAPWAP-5-SENDJOIN: sending Join Request to 10.10.1.100*Aug 13 13:56:07.5...
