Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
Configuration Sync Not Loading - Workaround
by mloraditch -
Firefox internet disconnect after Cisco Secure Client on macOS Tahoe
by mmathebula -
Meraki API Feature Request: Public API Endpoint for Splash Authorizati
by Icush -
Re: Ethernet uplink speed degraded
by RobertKozka -
Call redirect to multiple numbers
by chriswebb12581 -
Workflows RBAC?
by Jeff Orr -
Weird (but working) Port-channel configuration
by wpalumbo06 -
RA VPN termination on Loopback interface - FTD 7.6
by llomjaria
Community Activity
C9105AXI-EWC-A v17.6.4.56 stopped associating clients
Hi!I would like to ask if someone else is having or experienced this kind of issue. I have several C9105-AXI-EWC access points and they stopped working all of the sudden at the same time. Light indicator is steady green instead of the usual steady bl...
Resolved! cisco IOS XE Upgrade
Hello , we are using Cisco Catalyst 9300 as below in install mode and we have completely classical routing features etc. As we want to upgrade on Cisco Portal we have no more IOS Image with same Bengaluru series. I believe now we have option to...
SSID Reset to default
I hope we have soon a feature that lets admins reset an SSID to its default settings with one click. Right now, we have to manually undo every setting, which takes time and can lead to mistakes.Saves Time: Quickly resets an SSID without needing to ch...
Configuration Sync Not Loading - Workaround
Had to call support on this as configuration sync was not loading for any org. It's a known bug with the recent gui changes and no fix eta.Figured I'd share the workaround:This can be worked around by appending the URL with "?show_new_side_navigation...
Re: Ethernet uplink speed degraded
We are in the process of replacing MR52 with 9166, few of new APs went into 100Mbps mode but the MRs were working fine on the same cable. Does anyone know how is Meraki AP checking the "cable quality" and why it decides to go into 100Mbps mode?
Resolved! Firefox internet disconnect after Cisco Secure Client on macOS Tahoe
Environment Details:Operating System: macOS Tahoe (Version 26.x)VPN Endpoint Client: Cisco Secure Client v5.1.8.122 (AnyConnect Generation 5)Affected Application: Mozilla Firefox (All active branches)Observed Symptom:Immediately upon disconnecting a ...
Resolved! Backing Up the nvram_config File
I want to back up the configuration for restoration on a Catalyst 9200.There is an nvram_config file in the flash: directory. Can I restore the configuration by backing up and restoring this file? (copy nvram_config running-config)When I checked the ...
BGP EVPN VPWS - Cisco & Juniper - Traffic withdrawn
Hi dear community,I am facing an issue with the following setup :Ping is not OK for the BGP EVPN VPWS Service (Vlan / EVC 20).Here is the configuration of the involed PE :Cisco PE ISR1111:interface GigabitEthernet0/0/1 no ip address negotiation aut...
Meraki API Feature Request: Public API Endpoint for Splash Authorizati
SummaryExpose the existing revoke_splash_auth dashboard functionality as a documented, supported endpoint in the Meraki public API (api.meraki.com/api/v1).Current BehaviorThe Meraki dashboard provides a Revoke button on the client detail page for any...
cannot connect to vpn lab
im trying to connect to the vpn for the lab. Initially i was able to connect but eventually got disconnected. Now i'm trying to reconnect using the same credentials but i get the error login failed
OSPF Rib Decision
So, I placed 3 routers in my lab r1--r2--r3. I run area 0 between r1 and r2 and area1 between r2 and r3. And then I advertised similar subnet on ospf on both r1 and r3. What I saw in the routing table amazed me a bit.1.0.0.0/32 is subnetted, 1 subnet...
Resolved! Weird (but working) Port-channel configuration
Hello,I was looking through a part of my company's network that I have not previously seen and noted an odd port-channel configuration. The configuration involves a pair of 8k routers (IOS-XE) connected to a pair of 9k switches (NX-OS). These devic...
Workflows RBAC?
Is there a timeline or estimated release date for basic or advanced RBAC for Workflows (for SSO dashboard logins)? Basic:Meraki Dashboard Role with only access to Automation (Edit) or (Run)AdvancedTAG-based to allow a role to execute only automations...
Episode 39: A Platform for Computer Vision
Computer vision has enormous potential to help us see what's important in the world around us, without the need to be physically present. The Meraki MV Smart Camera opens the door to computer vision, especially thanks to its APIs, which allow develop...
Cisco ASA not sending syslog messages over VTI interface
Hello,We are currently troubleshooting an issue where the ASA is not sending syslog messages to a server that resides across a VTI tunnel.At the moment, the ASA does not appear to support configuring a syslog destination using a VTI interface (i.e., ...
