Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
2114158members
1452491discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

Catalyst Center - PoE vs non-PoE

Hi,It appears that Catalyst Center currently provides only Power-over-Ethernet (PoE) data.Are there any recommended approaches to obtain energy visibility for non-PoE devices?Thanks in advance!

nagi0 by • Community Member
  • 101 Views
  • 4 replies
  • 0 Helpful votes

nexus monitor session not working

what could be wrong? erspan src monitor ses not working . There is some traffic on PO that is source monitor session 32 type erspan-sourceerspan-id 20vrf defaultdestination ip DESTsource interface PO bothno shut!sh monitor ses 32session 32-----------...

Resolved! FMC 7.6.2 upgrade to 7.6.2.1

I have updated FMC to version 7.6.2. I’m wondering, since my FTD is currently running version 7.4.2.2 — should I first upgrade the FTD to 7.6.2 and then patch FMC to 7.6.2.1?Or, can I patch FMC to 7.6.2.1 right away and then upgrade the FTD to 7.6.2 ...

pvlan community on trunk to server

I have pvlan trunk port facing router with some pvlans, primary and isolated vlans. I also have access (community) and trunks with isolated ports and this all works ok. Problem is that I need to have trunk port facing host that utilize normlal and co...

DMVPN Hub priorities

Hi AllI have configured a backup DMVPN hub in our environment (single cloud), I expect all the queries, nhrp redirects etc to come from the primary one as I have configured a lower priority on the backup one, hub 1 is default 0 and the backup is 100....

Suggestion for Cisco

Hello team,Recently I have been wondering if there is a way that maybe I could suggest that Cisco develops a site like HacktheBox but for training and resolving various network scenarios which can be created by using AI to collect information from th...

cwalek by • Level 1
  • 32 Views
  • 0 replies
  • 0 Helpful votes

LED flashing Cisco 2802i

I have Cisco 2802i-e-k9 and after boot its flashing Green,blue,red slowly and it doesn't broadcast ssid. What is the problém? 

TRIXIK by • Level 1
  • 160 Views
  • 4 replies
  • 0 Helpful votes

N7K replacement

HiWe are looking for recommendations for replacing our existing N7K.Is someone able to guide us in the right direction...This is the current build:Mod  Ports  Module-Type                         Model              Status---  -----  ------------------...

Redbeanie by • Level 1
  • 869 Views
  • 7 replies
  • 0 Helpful votes

Resolved! Can not get Internet Access [or nat translations] on my ISRC1111

Hello   I am working multiple setups but this one was supposed to be easy, until it was not. I am sure I am overlooking something tiny, but nevertheless. Long story short; here is my config and I get not get any NAT translations and or any internet a...

TheGoob by • VIP
  • 633 Views
  • 30 replies
  • 0 Helpful votes

Isolated VLAN That Requires Internet Access Only

I am looking to find out the proper configuration for three ports on two 3750X switches to have an isolated network / VLAN that will NOT talk to any other network / VLAN in my environment and only needs internet access. I have two interfaces on one s...

Load more