Cisco Community

Backhaul Architecture for Wireless design

Hi, we have below architecture for backhaul design, where root and mesh access points are kept at the same height.1) 2 root access points (APs) are connected to the wired network.2) mesh APs are used only for backhaul—they do not serve clients.I wou...

Ftd osp/bgp

Hello, am abit new to Firepower configuration.. We have two ftd instances, one as campus and another as perimeter, both managed from fmc. The the two instances share routes via ospf peering, and bgp retribution also configured.The problem am facing i...

Migrating 4331 to Support WebEx Calling

Currently have a 4331 that is supporting an on-prem cluster of CUCM. Working on migrating users to WebEx calling, w/ the plan to still utilize the local 4331 for calling in/out. The plan is to do a phased migration, so I wanted to confirm that this...

Configure Linux to serve multiple dhcp servers / vlans on Nexus

aside from buying a Switch that does all this in one device, I am trying to connect my 7 vlans to their own DHCP Servers being hosted on Linux as the Nexus does not support DHCP Servers and the guest shell repository is no longer valid. In Linux ;...

Three way conference to play prompt

We are trying to build a script in Webex CC that collects digits (enter your phone number), then dials the external party, plays a greeting "this call is being recorded", then drops off, leaving the original and external party connected. We tried thi...

CML vManage GUI not working

Hello,I am running CML 2.8.1 and I cannot get the vManage GUI to work for some reason. I get the following error:I checked that the file is missing:Does anyone know why this happened, and how to fix this?Thanks,Juan

Account Access Issue – ERROR_VUE_WIDE_BLOCK

Hi,I need support with my Pearson VUE / CertMetrics account. When I try to sign in, I receive this error: ERROR_VUE_WIDE_BLOCK My only email used for Cisco is: Sultannasreldin@gmail.com Previously I had a Microsoft certification profile on Pearson VU...

Will the account be locked after multiple failed SSH logins to the N7K

Is there a configuration on the Nexus 7k device that locks the account after multiple failed SSH logins? Is account locking only for accounts with multiple incorrect entries or for all accounts?

PXE Guest Shell Question

Hey, I have a Nexus N9K-C93120TX and a while back I had installed the dhcp software on the guest shell, installed and was used perfectly. Since then I had shut it down and today went back to use it but decided to default the router back to stock and ...

请教各位大神 C1200-24T-4X交换机能不能实现交换机上的电脑或其他网络设备能正常获取IP而私接下级交换机的设备无法正常获取IP地址

请教各位大神 C1200-24T-4X交换机能不能实现交换机上的电脑或其他网络设备能正常获取IP而私接下级交换机的设备无法正常获取IP地址。而且不需要绑定MAC地址。如果可以实现。能麻烦把命令发一下吗

客户端MAC地址被随机BAN，无法使用无线

AC是9800-L。AP有1802，2702，9115三个型号。目前遇到的问题是随机拉黑MAC地址，时间不等。半小时或者十几天。IP地址池足够用。用AI查询各种排除方法都用过。 IOS版本从17.3.3升级到17.12.5 ，问题依旧。我有三个SSID，其中一个没有密码，默认的policy。也是同样的问题。情况有以下几种1.客户端无法连接SSID，使用随机MAC地址可以。2.客户端无法连接SSID，随机MAC也不行。3.客户端无法连接其中一个SSID，其它的可以。4.所有的SSID...

3560X switch upgrade IOS unsuccessful

3560x-48t-s upgrade IOS unsuccessful, c3560e-universalk9-mz.152-4.E10.bin, c3560e-universalk9-mz.152-4.E9.bin, both IOS tried, no, file MD5 validation is fine.

3560X交换机升级IOS不成功

3560x-48t-s升级IOS不成功，c3560e-universalk9-mz.152-4.E10.bin，c3560e-universalk9-mz.152-4.E9.bin，这两个IOS都试了，都不行，文件MD5验证没有问题。

ASA5512X Failover Communication Failure

I am using 2 ASA 5512Xs with the same bin, version 9.12(4).67 , hardware (4GB ram and clarkdale 2.8Ghz cpu), and license (security plus) but when I do show failover state it says there is a communication failure between the two. I am connecting them ...

3504 WLC Rack Mount Rear Bracket SKU

Hi, Is anyone able to assist re the exact SKU for the rear brace / bracket for the 3504 rack mount tray? The installation guide has information, but I'm having trouble translating this into a usable SKU to order. Any assistance would be appreci...

Community @ Cisco Live 2025 - Melbourne

Community @ Cisco Connect Canada

Celebrate our 25th Anniversary all year long!

Community Activity