Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
how to see the line vty session time-out in NX-OS
by Sudqi -
IPSec VPN "Up-Active" but No Traffic Passing Between Cisco and Bintec
by Thomas27100 -
the self-registration page of guest wifi portal is not being updated
by seanxiao -
Por que ainda tens o VTP (VLAN Trunking Protocol) ativado na tua rede?
by Silesio de Carvalho -
GRE over IPSEC
by georgesofroniadis -
Recommended action for Virtual Appliances upgraded to version 3.7.0
by gaushar7 -
Moving access points and clients from 5508 to 9800 WLC
by pthakkar -
EWC Client issues
by Wes Schochet
Community Activity
Resolved! Cisco CBS 350 ISE - Radius KEY
Hi! I am trying to configure ISE setting and when it comes to insert the radius password I am receiving the below error: encrypted radius-server host 192.168.1.2 key 7 143542050805263F75 OR encrypted radius-server host 192.168.1.2 key 14354205080526...
Moving access points and clients from 5508 to 9800 WLC
So we have old 5508 controllers in our environment which has access points and clients on them. We also have 9800 WLC in our environment on the same switches. We are planning to move the access points and clients between the two controllers and wante...
CSAM || Problems with CBRAdmin association (Case 3)
Hello team, Recently we are having some problems with several customers regarding the association of the CBR Admin role in CSAM, I have already validated all the points necessary for association, which are: 1. Confirmation of the need for a valid Sma...
EWC Client issues
Hi All-I am upgrading a small site from an autonomous 3602 to a 9120 EWC. I have a bunch of IoT devices that are having problems connecting. Theie sessions fail about 50% of the time. Debug analyzer shows this:Time Task Translated2024/10/10 03:39:...
Use Nexus 9000 as Layer 2 LAN switch
I have a Nexus 9k that I'm trying to configure as a basic L2 switch like all of the 2960X switches we have on our network. I have an etherchannel configured between the Nexus 9K and out Cisco 6807 core. All of the routing for our inside networks is...
CSAM || Problems with CBRAdmin association
Hello team, Recently we are having some problems with several customers regarding the association of the CBR Admin role in CSAM, I have already validated all the points necessary for association, which are: 1. Confirmation of the need for a valid Sma...
9100 AP transitioning from local to Flexconnect mode in N+1 scenario?
Hello experts, We are considering deploying N+1 WLC in a regional basis. The requirement is to have a backup WLC in the regional site in case the local WLC presents a failure or is unreachable for long periods of time. My question is if such an AP co...
Resolved! EIGRP Metric Calculation
Hello everyone,While learning EIGRP, I encountered a challenge regarding metric calculation. I understand that each router calculates the Feasible Distance (FD) to reach a destination. As part of this process, each router first calculates the cost to...
Video - Revolucionando la Ciberseguridad: Dominando XDR Automate
Grabación del webinar Community Live Video con nuestros expertos Nayeli Calva, Brenda Márquez, Uriel Islas y Uriel Tadeo Montero. ¿Qué es XDR y cómo funciona? Dentro de Cisco Extended Detection and Response (XDR), contamos con la herramienta de "Auto...
Configure Application Server down alarm ISE (Identity Services Engine)
Good afternoon.I need help to configure an alarm to warn that the Apllication server service is not running or is initializing. The ISE version is 3.2.0.542 Patch 6. Best regards.
Doc - Revolucionando la Ciberseguridad: Dominando XDR Automate
Presentación del webinar Community Live Revolucionando la Ciberseguridad: Dominando XDR Automate Con la colaboración de Nayeli Calva, Brenda Márquez, Uriel Islas y Uriel Tadeo Montero. Descubra en esta sesión cómo utilizar la herramienta de Automate ...
Cisco 5508 WLC v.8.5.161.0 doesn´t work via GUI but does work via SSH
Cisco 5508 WLC v.8.5.161.0 doesn´t work via GUI but does work via SSH. It used to work and then it stopped working. The web mode option is enabled. Any help or a similar case?
CSAM || Problems with CBRAdmin association (Case 2)
Hello team, Recently we are having some problems with several customers regarding the association of the CBR Admin role in CSAM, I have already validated all the points necessary for association, which are: 1. Confirmation of the need for a valid Sma...
Monitoring Traffic Consumption by MAC Address
Dear Team,I am currently using the Wi-Fi Mobility Express model AIR-AP1815I-I-K9, with WPA2 Personal authentication and MAC filtering enabled.Is there any way to track the traffic consumption for each MAC address on a daily or weekly basis?Thanks in ...
MacOS 15 and Anyconnect 4 conflict?
I just want confirm that cisco anyconnect 4.10.04071 is compatible with MacOS 15.0.1. I have a client that is trying to use that software but keeps getting errors saying that the application quit unexpectedly as soon as she tries to open the software...
