Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1990056members
1346969discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

Resolved! Destination vPC VTEP Address for ACI

Hi All,We're using ACI in our environment and ran below command. I am not able to figure out on which leaf the tunnel destination "10.9.152.77" resides. I think the tunnel destination is the VTEP assigned to a vPC. How can we search it centrally and ...

dhr.tech1 by • Spotlight
  • 97 Views
  • 3 replies
  • 0 Helpful votes

AD lockouts occurring from RA-VPN brute force

Scenario:I am trying to figure out a way to prevent AD accounts from being locked out when brute force login attempts to the RA-VPN occur.RA-VPN configured on FTD. Radius authentication used via ISE pointing to AD. DUO MFA works fine, no issues, but ...

tmcG by • Level 1
  • 36 Views
  • 2 replies
  • 0 Helpful votes

Resolved! WebEx App Audio Crash

I have noticed an issue with the WebEx app: it will crash when the Ringers and alerts audio is set to All Devices, the volume adjustment bar is adjusted to very low, and "Automatically adjust volume" is disabled. I will then close the WebEx app and r...

FTD Migraton Uisng FMC

HiI dont have access to a  lab so am asking a couple of questions'I want to migrate from one FTD to an HA pair, On the FMC thats is currently managing the single FTD there is a sub doamin for the FTD but on the new FMC where I want to migrate the FTD...

BE7K Built in LAN1 and LAN2 Ports

We are trying to setup some redundancy for our BE7K's (BE7H-M5-K9) links by using a mix of ports on the motherboard and PCI cards as recommended in the Install Guide.The install guide lists the three ports on the motherboard as "Dual 1-Gb/10-Gb Ether...

bacase by • Level 1
  • 37 Views
  • 0 replies
  • 0 Helpful votes

Copy text/phone number from Voicemail Page

Is there a way to copy the text of the phone number of a voicemail that has been forwarded so that it may be pasted in the Calling Dial pad to call the person that left the voicemail back, instead of using the green Audio button that calls back the p...

LuSt by • Community Member
  • 33 Views
  • 0 replies
  • 0 Helpful votes

Resolved! PDMT cannot migrate WLC

Hi, Wondering if anyone has run into the following issue. Trying to migrate Prime to DNA center using the inbuilt PDMT but everything works except the WLCs will not migrate to DNAC. I've turned off SNMP v1 and v3 on the WLCs to no avail. One thing to...

elemzy01 by • Level 1
  • 585 Views
  • 3 replies
  • 0 Helpful votes

Firepower 7.42 issue interface Management0 has no link

I'm in the process of upgrading all of my firepower devices from 7.2.8 to 7.4.2 as it is the suggested release. we use the data interfaces as the management interface for most remote devices. As I upgrade each one, I'm now presented with a critical w...

Lee Dress by • Level 1
  • 110 Views
  • 4 replies
  • 0 Helpful votes

Firepower 1010 readiness check stuck at "Please Wait"

I have a Firepower 1010, on 7.0.0-94 that I'm trying to upgrade to 7.4.2-172. I ran the readiness check last night at 8pm.   12 hours later, at 8 am, it still says "Please wait" on the readiness check, and won't let me hit the upgrade button. Followi...

Load more