Hello All - Just looking for help to understand some basics in choosing Spine and leaf in ACI. In a Datacenter, we use - ACI Spine as Nexus N9K-X9732C-EX (Sup-A) with firmware aci-n9000-dk9-13.2.4e.bin- Leaf as N9K-C93108TC-EX with image aci-n9000...
Hi Folks, we are in a process of designing and planning a multi-tenant ACI fabric. We have come up with AS number 65510 for the MP-BGP route-reflector policy. This will be for the leaf to spine MP-BGP session. We are wondering do we need to use the s...
Hello All , I have a setup where two Firewalls will be installed within the fabric as a cluster . Service graph with unmanaged mode will be used . The N-S will have service graph and E-W will have service graph as planned to be implemented , is this ...
Hi team when im going to deploy service graph in MSO it shows below error,Bad Request: Provider EPG DB-H2B22-ML_EPG must have subnet configured for service graph SGT1What will be the issue for this ?
Hi team when im going to deploy service graph in MSO it shows below error, MSO unable to deploy SG giving error , Bad Request: Consumer EPG_1 must have subnet configured for service graph SG_INFRA What will be the issue for this ?
We are planning to migrate our existing infrastructure to ACI in few steps. First to a Network Centric setup (EPG=VLAN=BD) with a L2 connection to the legacy infrastructure, migrate L3 to ACI and finally to an Application Centric design. Now, the qu...
I am using http method GET to get the AEP details by using the below API:/api/node/mo/uni/infra/attentp-<AEP_NAME>-aep/fltCnts.json?subscription=yesHere, very rare I get a response & most of the time I get error 405.{"totalCount": "1","imdata": [{"er...
When doing a fabric discovery on an ACI fabric with QSFP only leaf nodes, is QSA with 10Gbps SFP+ the only supported way to connect the APIC fabric interfaces to the 40Gbps leaf nodes? Is there any backdoor way to enable breakout support on any inter...
This topic is a chance to discuss more about the migration options from existing network designs to Cisco Application Centric Infrastructure (ACI). In this session the expert will discuss and answer questions that helps to understand the design consi...
Hi community,When configuring contract subject for PBR, I came across the different EtherTypes supported by a filter:- IP (I assume both IPv4 and IPv6)?- IPv4- IPv6- ARP- TRILL (not used in our DC)- FCOE (not used in our DC)- MACSEC (not used in our ...
I am trying to attach two identical baremetal linux servers with Mullanox 40Gig cards to ACI fabric. One to Leaf103 and another to Leaf104. Both Leaves are C9336C-FX2. I am getting no light on the switch interfaces or on the NICs. LED on the leav...
Good Morning,We are trying to configure PIM inside fabric (without external L3 itcx), but doesn´t work. We have deployed 4.0(3d) release and we have seen PIM with static RP is supported from this version. Have somebody configured it sometime ?Thank ...
Hello peaple:I used the followings commands on nexus 9000 switch: execute the command “setup-clean-config.sh"• execute the command "ls -al /bootflash/aci-n9000-dk9*". This will list the ACI switch imageson the current leaf or spine node.• execute the...
After doing some research, it appears that the most recent version of ACI (4.0(2c)) supports Hyper-V 2012 and 2016. I'm working with a customer who is hoping to upgrading their Hyper-V environment to Hyper-V 2019. Is there any targeted dates or code ...
Please note, I am no where close to be a SAN expert/specialist... Here is the scenario:Customer has two DCs (Primary and DR). Both are using FC SAN for storage (Brocade 7800). Customer wants to migrate to ACI, ACI Multi-Site particularly. The connect...
.jpg "VIP Advisor"){kind=icon}
