Has anyone got ACI Sim working on Proxmox ? I have unzipped the 5.2.4d OVA and then imported the OVF but when I try to start the VM it just hangs at: Booting Insieme Fabric Controller 5.2.4d on / rfs1 in 0 seconds ... I have assigned 64GB and 12 ...
Forum Posts
Here is the use case: I have two ACI sites (A and B) and running as multisite architecture. Each site has its own local only networks and there are also networks are L2 stretched between the sites. Each site has its own local L3Out (EIGRP based as an...
Hi Cisco Community,I am encountering an issue while trying to download the Cisco ACI Simulator 6.0(1g) OVA files from my Cisco account. Specifically, I receive the following message:"Entitlement Required. Click for support."However, I am able to down...
We have ACI fabric connected to FI6300 and further down to UCS chassis which are hosting our production ESXi hosts and vCenter, the VMM has been running for years.Now we have FI6500 and UCSX chassis installed, we would like to utilize the new UCSX in...
Resolved! NEXUS
Hi,I am facing some issues while converting the 9000 NXOS to ACI mode and need some inputs on this. Version information: SoftwareBIOS: version 05.39NXOS: version 9.3(2)BIOS compile time: 08/30/2019NXOS image file is: bootflash:///nxos.9.3.2.binNXOS c...
Hey all I am trying something that is maybe a bit strange, but it would safe me an L3Out and assigning some additional subnets.. I have a Nexus Dashboard and a very small ACI fabric (no other Nexus switches anywhere) and subnets as well as addition...
Hi,We are trying to get a 40/100 SRBD optic to work in our 100g switch. I can see the optic in both the spine and the 100g, but there is no link between them. Tried new cables but nothing. I have tried the 40/100 in port 36 and in port 28 of the 1...
Hello Guys, i have a Cisco ACI fabric (5.3) and i would like to configure an L3out with a cluster of checkpoint in A/A. On the legacy infrastructure i have pinned the muticas address of checkpoit to its ip address is there a way to copy this kind o...
Hello everyone,I'm new to this community and super excited to join the discussions here. I have a big curiosity about something I'm working on right now.I've just added a few new leaf switches to my ACI fabric and I'm planning to set up vPC pairing b...
Greetings, all,I have an endpoint that keeps going into a freeze state and I can't figure out what is going on and how to resolve it.The MAC address and IP addresses in question are physically assigned to the "IPROUTER2" host, but based on the EP Tra...
Here is a simple scenario to show the questions I would like to get some clarification regarding EPG and ESG. I currently have 3 EPGs for VLAN 10, 20 and 30. intra-EPG isolation is not enabled. Each has a number of workloads/endpoints included and un...
Hello,I have a L3 routed connection between NX-OS switch and ACI Leaf, When I run "show cdp neighbors eth1/1 detail" on the NX-OS switch, it shows me a different ip address than that of the direct interface! it seems to be a L3out interface address e...
Hi All,This is not a new setup but currently we are doing migration of one of our L3OUT firewall. Old one is cisco ASA and we are migrating to Palo Alto Firewall. Post migration couple of our subnet which is supposed to be advertised externally is no...
We are observing our ACI fabric health score is not changing, we are seeing the events in logs. Observing this issue in all leaf switches.APIC Model = APIC-SERVER-L4Leaf Model = N9K-C93180YC-EXFirmware Version = 5.3(2b)
We are migration our ACI infra from old DC to new DC. Can you guide in the best migration process with least downtime. Some challenges :- 1. Old DC and new DC separated by 5 kms. (will need to change SFP to long range type , speed change from 100g to...
