Application Centric Infrastructure

ACI DHCP Relay

Hi, I have an EPG configured in a User Tenant with a requirement to access a DHCP server located Externally over a L3Out. The EPG and L3Out are both in the same Tenant-VRF. I have created a DHCP Relay Provider within the User Tenant with the EPG type...

Get FDB table via SNMP in Cisco ACI

Hello, Is it possible to get FDB table via SNMP in Cisco ACI? Regards, Dmytro Morozov

ACI SNMP V3

Good afternoon, Are there any issues configuring ACI to use SNMP V3. The SNMP management station can poll the ACI APIC's when configured to use V2. However the APIC's do not respond to management polls when configured to use SNMP V2. Any help appreci...

Resolved! How to find ALL EPGs that assign to an interfaces or VMs Domain?

Hello Community, I think this feature has been requested somewhere, I hope to put more traction to Cisco Dev to provide an effective way to find ALL EPGs that an interface is associate with. As we are moving from traditional network to ACI, the num...

Issue when upgrading APIC

Hello everyone, I recently started by upgrading my controller (APIC). Our target was the 2.0.2f and there was initally the 1.1.3f on our hardware. So as we've seen from cisco, we needed to go through the 1.2.3 before trying to reach the target. (2.0...

Resolved! Failure tolerance in ACI

I have a question about the failure tolerance in ACI. My setup are 3 leafs and 2 spines. Usually its ok if one link is dead because the leaf would use the other spine.Attached to this discussion is an example that shows two endpoints which are trying...

Static Routes spread over ACI leafs

Hi, i'm going in a while to approach the study of a "Grownfield to ACI Greenfield" migration process for a customer. Among the many aspects to be analysed, one of them is the following one: - at the moment the customer has a classical double-side vP...

Resolved! EPGs

Hi all. I have only played with ACI on dCloud and have read whatever I can find from resources online. We don't have a live ACI-infrastructure (yet). There are some questions I cannot seem to find answers to, and hope that some of you can enlighten ...

ACI L3out with SVIs

HiWe've got 2 ACI fabrics (not linked) and are now nearing the end of the migration of services from our old Cat6500 DC switches to ACI. One ACI fabric is in our main DC, the second is in other backup DC (although a couple of live servers do run ther...

ACI-DQ authorization

Hi all, can anybody let me know ACI-DQ authorization is all about? Many thx, jj

Tunnel Interfaces - ACI

I have 4 Spine switches and 16 leaf switches in my ACI environment Under the Fabric, below each node, (Spine or Leaf) I could see a number of tunnel Interfaces configured. When I check the EPG Information of a specific server under the Fabric Inven...

L3 Routing in VRF

I have created a L3Out - External Routed Domain under Networking. There is a VRF associated with this External Routed Domain. Under Route Control Subnet I have defined as 0.0.0.0/0 to exchange routes with my external device through the OSPF defined ...

Resolved! ACI - Any feedback about 2.2(2i) version

Hi,I'm currently running the 2.1(1h) in production. I would like to upgrade to the newest version 2.2(2i).Do you have any feedback about this version (stability,issue...) ?Regards,Ju

ACI API request to get full APIC configuration

Is it possible to pull down the full APIC configuration via the API. Rather than making API calls for nodes, tenants, vrfs etc. separately? I haven't been able to find a way yet. If so , what's the url for the GET request? Also, is it possible to pos...

APIC not register on Production

I have issue about not register apic1 and apic2, and i can not access apic from gui. I only access apic from cli/ssh with user : rescue-user what problem ? any clue how to fix thanks