Can someone help me with command used to check which EPG is linked to which VRF in cisco apic 5.2
Can someone help me with command used to check which EPG is linked to which VRF in cisco apic 5.2
L3OUT and IPN/ISN connectivity termintaed on the same device. How do we prevent asymmetric routing for incoming traffic.For example for traffic going to ACI site B, how do we make sure that retrun traffic use IPN/ISN link and not the L3OUT to reach A...
Hi, On an ACI switch there are several scripts available like `setup-clean-config.ssh" to reset the switch. But, there is also script called `setup-admin-ssh.sh`, for which I cannot find any info. Does someone know what this script does? what it is ...
Hi Everyone, I'm deploying the MultiSite ACI for one of the customers. The cusomer has a naming standard. I'm a bit confused about choosing the names for the spines and leafs. I have 2 sites: Ballarat and Midland From the management perspective I ten...
Is there a command that will show me all vlan encap's that are configured?
Try to understand how remote leaf multicast works in the multisite with multipod environment. As I know, when creating the multisite, it will assign a unique Overlay Multicast TEP(O-MTEP) per site, spines of all the pods within the site will have the...
Hi everyone, I have configured ACI Data Plane Policing and assigned it ingress to an IPG used by a L2 interface. So far so good. Now I need a way or CLI command to view the policing/rate limiting statistics similiar to "show policy-map interface" in ...
I understand it to be a best practice recommendation to have a unique VLAN encap per EPG, and to always use the same VLAN encap for a given EPG. Is there a way in the GUI to show if a VLAN encap is/isn't used in the fabric?I know the APIC will preve...
Hello, our current ACI fabric is running 4.2(7), 14.2(7) and we want to upgrade to 6.0(2). Existing spine and leaf switches hardware are not compatible with 16.0(2). Can i upgrade the APIC only from 4.2(7) to 6.0(2) and leave the fabric switches in t...
Hey everyone!So I'm trying to upgrade my fabric to the latest version and I'm just stuck, nothing happens for more than 2 days already.anyone familiar with the issue?
I have the 3-node physical ND appliances running v2.1(2d) with NDO v3.6(1e) for ACI multi-site. 1. Does ND and/or NDO have the capability to send email alerts/alarms? I assume no as I did not find any options regards.2. How can I generate a CSR on ND...
Dear All, Would like to know and understand - How DDoS attacks has been identified in Cisco ACI (towards controlles). Is there any inbuilt feature in Cisco ACI to detect and prevent the DDoS attacks.Regards****
Looking for suggestions on troubleshooting this issue. An endpoint running on VMware DVS (v7.0) port-group which was created by VMM integration with the ACI. ACI assigns dynamic VLAN to the port-group and hosts the default gateway under the EPG asso...
In our lab environment we're trying to build multipod over an MPLS network with Nexus 7k's acting as the IPN routers. We've run into a number of problems, but now the latest is that endpoints in pod2 can only ping the anycast address of the bridge-d...
[Apologies if you have already seen this: I accidently posted it in /Service Providers/MPLS/ and found no way to move it] Hi,Let me start by saying I suspect I know the answer, but am hoping someone with more knowlwdge than I have will be able to ela...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-11-2024 01:42 PM | ||
07-11-2024 03:28 AM | ||
07-09-2024 12:08 AM | ||
07-08-2024 02:37 AM | ||
07-05-2024 04:40 AM |