Application Networking

Dear Techies,I am performing a deployment, in which i require clarity on the following. Our setup has DC and DR , in each site we have two devices for HA.We have received One SSL Certificate from Public CA, Kindly clarify the following doubts i have ...

Hi Folks,Can anyone assist with a fix for the following issue on traffic through the ACE module? TCP sessions are being reset after 60 minutes of inactivity (default behaviour I understand). I need to extend this to 7500 seconds. Our ACE sits betwee...

Hello,I need to clear an entry that appears in the FIB table of a context of our ACE module:# sh ip fib | inc 6.34x.y.6.34/32     N/A                 DROP   V [0xc00](I masked the 2 first numbers of the IP address with x.y)This entry appeared after I...

The SRE-700 comes configured with 2x2M DRAM. I have an SRE-700 with 2x4M DRAM installed but it gives alarms about unsupported configuration as 8M although it is working and optimising traffic. I want to remove one of the 4M module but not sure if the...

Hi,We use the default value copy of the dscp today in the waas's.Is it posible to have dscp mark change per application/port?So RDP "tcp/3389" use an higher dscp value, than the other default.We use 5.0.3 in the CMA and 4.4.5d in the WAE'sRegards Jan...

Hi..I am having WAE-7371 and WAE-574 in my network and planning to migrate my network to IPV6.. At present running IOS  in my network is oe574-4.4.5c.4 at CM and oe574-4.1.1c.16 at Sites and oe7371-4.1.3a.32 at DC/DR..Please help me out to get the IO...

hello, i have experience 3 new unit from Cisco that keeps rebooting. Is there a way to restore the image or RMA is the only solution.thank you

Hi I would like to know... if someone knows how to size a Load Balancer. If i dont have statistics, what is the best way to size a load balancer1. Size of the Internet Connection - 10 Mbps 2. SSL offload ..........unsure 3. Number of Webservers 2 reg...

Hello, I have a cisco balancer and I want that the urls (www.web.com/blog, www.web/eco and www.web/info) traffic will always go to specific server, but doesn't works.This is my settings:ssh maxsessions 1access-list ANY line 8 extended permit icmp any...

Hi,Recently, we have tried to migrate one of the web services that is fronted by the Cisco ACE 4710 and we observed that some of the HTTP packets were dropped by the ACE 4710 as the maximum parse length (e.g. HTTP header) exceeded the default length ...

I have two serverfarms, S1 and S2.  I need S1 to probe S2 and if S2 servers are all down then I need all the servers in S1 to be taken down.   This is what I was thinking.  I would prefer to script this all out and use a single probe, but I'm not sur...

Everytime I make a config change to one of the contexts on our ACE20, I get this message:Config Application in Progress. This command is queued to the systemIf I run show download info, I get:context : context1Interface                     Download-s...

I am in the process of migrating from the CSS to the ACE. Our CSS setup was routed mode, so I've built the ACE as routed mode. The issue I struggle with is the server side vlan is strictly for web servers. Previously the web servers had a 2nd NIC for...

Users are getting intermittent http 409 error when they are in a specific UI on the web page served thru an ACE 5520.I can't find anywhere that would casue me to believe these errors are being generated from the ACE, but the application and server te...