Hi allI'm running a ACE10 blade doing SSL offloading.sample config from our setup:ssl-proxy service SSL-NGINX01-WILD key wildcard.xxx.com.pem cert wildcard.xxx.com.pem chaingroup xxxx.COMpolicy-map multi-match XXX class VIP-NGINX-XXX ssl-proxy se...
Hi allI'm running a ACE10 blade doing SSL offloading.sample config from our setup:ssl-proxy service SSL-NGINX01-WILD key wildcard.xxx.com.pem cert wildcard.xxx.com.pem chaingroup xxxx.COMpolicy-map multi-match XXX class VIP-NGINX-XXX ssl-proxy se...
I saw a discussion in regards to this further down but didn't see a definitive answer to my particular question.To register my appliances back to the CM after I've changed the IP address of the CM. Do I need to first deregister the old CM IP and then...
Hi,This topic has come up in the past but have not seen a clear proper answerFor a CSS with a SSL module (performing SSL termination) - is it possible to impliment a redirect on https URL to send to equivalent http URL Client > https://www.site....
Hi!Has anyone tested if you can use inband health monitoring on the ACE to detect a failed server, remove it from loadbalancing and then use an active probe to put it back in service as soon as it is online again? Will it work? Or is "resume-service ...
I am trying to setup 2 ACE in a FT mode. While both are active, I am all goodMy questions are:1) If I unplug the primary ACE Network cable, I loose connection to my HTTP servers (via VIP address) and my ping to the VIP failes, eventhough the second...
Hi,I configured conn reuse and I tried to provide requests from diferent clients to the VIP address (172.16.11.150). The ACE provides load-balancing, but it doesn't provide conn reuse. The server uses the same MSS as ACE (1460). See the configuration...
I am runng WAAS 4.1.5fstarted geting %WAAS-CIFSAO-3-131207 Error replying to client 172.16.6.167. yesterday,( about 5000 messages per hour) seems to be only on this central site servercleared by the "no accelerator cifs enable" command the re-enabli...
Does anyone know how to trace firewall and load balancers in datacenterAs i was drawing the network design of my existing datacenter i am able to trace router and switches but was unable to find the firewall and loadbalancer please do help if anyone ...
So far, all documentation that I read, WAE is used in conjunction with Cisco devices. Can WAE be integrated with non-cisco devices? I guess, In-line mode should work ok, but how about off-path mode? An example or link will be appreciated.Thanks!Jo...
Hi!I have two Load Balance ACE4710, one is Active and other is Stanby. I have configured PROBE UDP SIP so. I can see that in the LB active sometimes the probes are SUCCESS and int the other LB stanby are FAILED. and after sometimes the probes are su...
Hello allWe recently upgraded an ACE module from A1 code straight through to A2(3.4)Theres a behaviour change we werent expecting -probe tcp t2-probe-3133 port 3133 interval 4 faildetect 4 passdetect interval 4 passdetect count 4 receive 1serve...
I am very new to WAAS technology, please forgive me if i ask a dumb question.I have been reading Cisco Live power point presentation slides and books, it seems that it is not a good idea to configure WAE to use hsrp ip address on head-end WAN router....
Hello,I have ACE 4710 that load balance two cach flows (bluecoat), i am doing pbr on the routers to send the traffic destined to port 80 to ACE then Cach farm. After that the Cach flow will get the page from the internet via two routers. The return t...
running CSM-S with 2.2.(5)....I need to do the following on the same vserver:==========================================================Point 2) and point 3) should take precedence on point 1)1) URL /*From http://mysites.ams.pippo.com to http://mysit...
Hi all, I have a doubt regard to a configuration.I have a router that uses as default gateway the ip alias of its own ace module.1)How can I predict the routing? Do I have to check the static routes configured in the Admin context in order to underst...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
03-06-2024 12:27 PM | ||
02-21-2024 04:21 AM | ||
10-04-2022 06:16 AM | ||
09-26-2022 11:58 AM | ||
09-13-2022 02:40 AM |